4KSRS25CHT00 KitchenAid Refrigerator - Instructions

Had a 1999 Kitchenaid Superba refrigerator that quit making ice. Based on online research, my icemaker's problem could have been either the icemaker itself or the dual water valve. I opted to try the icemaker replacement first after watching the helpful installation video. The only issue I had that made the repair the slightest bit difficult was that bolt-headed screws were used to secure the icemaker to the fridge wall rather than Phillips and the one nearest the door can't be seen while trying to loosen it. It only took an extra ten minutes to overcome this obstacle (maybe 20 minutes total). After replacing the icemaker, I thought the water valve must have been the problem after all since the unit did not immediately start filling with water. However, once the unit chilled down, it worked perfectly.

Loosened 2 screws,un pluged the wiring harness,pluged the new ice maker in,tightened the 2 screws. . And I now have ice!! Very easy to install. .

Found the replacement icemaker I needed on your web site,ordered and recdeived it within 2 days. Watched the how to video and did the replacement in less than 5 minutes.However,I waited(2 days) for the icemaker to start working, it never did. Thinking there was another problem in the icemaking system, I contacted a local appliance repair shop. They checked the entire system and everything was ok except the new icemaker. Turns out the new icemaker was defective. I contacted PartSelect and reported the technicians findings. I had another new icemaker in 2 days again. I again installed the new one and am now making ice. Thank you for the installation video and the teriffic service.

determend o.k. water flow,determend solenoids o.k.problem had to be ice maker.ordered part on Su. eve.,recieved new part Tue.A.M.,had part installed in 15 minutes. Then waited for quite a long time untill it finally made ice.

Very simple. Using only a screw driver removed all the screws and removed the front part of the ice bin. Then I removed the screw auger that pushes the ice out and reassembled every thing to the new ice bin.

Removal of escutcheon was easy. Replacing icedoor was fairly easy, working with wires in the way was a little distracting but simple. Be careful with microswitches and locating pins. Two of mine broke, had to replace bracket. Simple job again. Everything working fine now. No ice jam in chute. Using needlenose pliers to remove/insert pin is the best and easiest option.

Per directions supplied

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones

Removed the old one. The new one had a power chord attached but it did not connect to the wire in the freezer. I saw it could be unplugged from the new ice maker and the power chord from the freezer plugged right in. Once installed, was not sure it worked but after a few hours it filled with water and started making ice. Works great now.

Lower door closing cam was completely worn down so door wouldn't close on it's own. Ordered parts which arrived in a couple of days. After watching installation video on this website the job looked pretty easy. Needed socket wrench to loosen nuts at top, they were really tight. Removed door. Replaced both the cam on the bottom of door and the cam on the main unit, put door back on making sure it was straight and lined up properly. Retightened top nuts securely. Voila, problem fixed in only about 15 minutes or so.

I just wanted to tell about the good service they gave to me. The first one I received was broken, and with one phone call they sent me another, no problem. Installation was take the broken one out and replace it with the new one.

I have a side by side so the space to work in was limited but I still completed the install in about 30 minutes. Unplugged the refrigerator then loosened the top two screws took out the bottom screw lifted the ice maker out just far enough to disconnect the power cord reversed the procedure. plugged it back in started making ice in 30 minutes. Probably would have not have taken that long my MS slowed me down a little. The repair man was going to be $300.00 plus $$75.00 trip charge what I paid was $128.41 that was with 3 day shipping.

If you are having this problem, read this. My refrigerator door would not stay closed. This was over a year and a half time period. I thought it was something complicated and told my wife to call a repairman. Thank goodness she does what she does best - not listening to me! I finally had enough and went online and googled my problem and found PartsSelect. PartSelect had a repair video showing how to fix the problem. If you are like me, I'm very cautious about purchasing from a website in which I'm not familiar. PartsSelect is a reputable site (I promise I do not work for them). My refrigerator is over 8 years old and they had the part I needed, a lower door cam, along with a video on how to install the part. This honestly took about 5-10 minutes to do and I did it without any help. I was so aggravated at myself for waiting so long at doing this!! I actually ordered 2 of these parts, just for the next time. You can do this.

unplug frig, didnt turn off water used cord light to see. Took 1/4 nutdriver and loosen screws removed screw on bottom bracket uplugged ice maker. reversed the process for the new one and done

Once we figured how to get front off, it was like a puzzle. One piece at a time. So thankful part has been improved and replaced. It works better than before, just wish would have done it sooner.