Models > 4KB25G1XGA5 > Instructions

4KB25G1XGA5 KitchenAid Mixer - Instructions

All installation instructions for 4KB25G1XGA5 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the mixer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4KB25G1XGA5
31-45 of 105
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

teeth missing on worm gear

  • Customer: Ronald from Anna OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
removed cover annd snap ring removed gear and replaced with new,

gears were stripped from overload of bread dough

  • Customer: karl from Eureka MT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
At the back of mixer is 1 screw that holds metal band. Remove to reveal 4 screws that hold top half of mixer. Inside locate transmission housing remove 4 more screws. Inside housing carefully scrape away grease and broken bits of gear. Take out worm gear drive shaft wipe off and inspect. Clean up grease inside tranny locate keeper ring on vertical shaft spread and slide off use 2 screwdrivers to jimmy gears up. Replace with new parts put back together and use fresh grease. Not too hard at all and alot cheaper than a new kitchen-aid.

gear teeth worn off worm gear

  • Customer: Jamie from Jamestown ND
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
replace worm gear

The mixer only ran on high speed

  • Customer: Kenneth from Clovs CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I replaced the speed control board, however that did not correct the problem. I received the part very quickly and the install was easy but obviously it did not correct the problem so I will be returning the part. Hopefully that will go well also.

Last repairperson broke the top cover of the gearcase ; still need this part .

  • Customer: conradt from el paso TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Easy ; remove belt ( 1 screw ) remove cover , and there is the complete drive . I still need the top plastic cover which is cracked and broken where the bolts go through . Please quote this part .Conradt

Plastic boke on the old thumb screw

  • Customer: Alice from St Louis MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!

speed control went. The beater would fly in any setting

  • Customer: Brandy from Thorp WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
I carefully removed the cover of my mixer. I first made sure that all of my part numbers corresponded, then I labeled the 5 wires that needed to be disconnected. I then disconnected the wires, removed the two screws holding the part in place, switched out the old for new, reconnected all of my wires. Mades sure everything looked tight, and put my cover back on. Works like a charm. I cried because what I really thought was going to be a $200+ fix, ended up costing me less than $50! And it was so easy.

Gears were stripped and mixer would not mix

  • Customer: Gregory from Califon NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
This was easy once Igot all the parts. The mxer wouldn't mix and when I opened it up the drive gear between the motor and the planetary drive was missing some teeth. Turns out the bearing, which was sintered bronze, had broken so I needed a new gear, new bearing, and the jumping gear had broken the housing so I needed a new housing. The new gearing ( really a bushing since there are no rollers or balls in the "bearing") waws now steel and the molded plastic housing is now cast metal. Some new grease ( I had to buy a quart can of grease to get two tablespooons) a new gasket and put the screws in and we're back in business. Total repair time 10 minutes, total time to get all the parts 3 weeks,

plastic outer casing on tightening screw had broken

  • Customer: Peggy from Escondido CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!

mixer was very noisy when running and made a horrible grinding sound

  • Customer: Thomas from Bluffton IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
My husband removed screws and took top off mixer. Then he took out the gears and cleaned them from all the grease. After he did that he could see the gears that were all worn. We went on line ordered the new gears and in a couple of days the parts were here and he put them back in and greased it all again and put the top and screws back in place. Mixer sounds much quieter. Thank you.

Household (stand) mixer making weird noise

  • Customer: Linda from Anchorage AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed 4 screws on mixer top. Removed 4 screws to gear box cover. Ordered replacement gears from Parts Select. Removed snap ring. Repaced two gears. Applied gear grease, replaced snap ring & screws. Gears at local appliance dealer were $39 each. Total parts from Parts Select + shipping under $20, received in 3 days!

thank you,

  • Customer: Eleanor from Perry NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
my hasband did the work and i an so happy it is working good for me now,

Mixer Feet startarted to disintergrate and leave marks on counter

  • Customer: Vernon from Orange Park FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 1 people found this instruction helpful
Called original Kitchen Aid and advised had been sold and to look for Kitched Aid on web. Found site, went to appliance diagram and obtained part number and ordered. When parts came in just unscrewed and replaced new feet.

Replacement of digital window in oven unit

  • Customer: Bedalia from Rialto CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
I did not do the repair myself, however, I contacted a suggested service company which in turn was a company I had used before when I had problems with my JenAir microwave. Excellent service, prompt and very professional. Thank you JenAir for your assistance in providing promptly the parts needed to complete this job.

none

  • Customer: Joseph from Mentone CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.
All Instructions for the 4KB25G1XGA5
31-45 of 105