4ET20ZKXDN01 Whirlpool Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replace hinge bracket on fridge door
taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.
Parts Used:
-
Albert from Dunmore, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Switch didn't work
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Parts Used:
-
Don from Laramie, WY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
exchange of defective light rocker switch
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
Parts Used:
-
Steve from River Edge, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
I broke the damn thing in the sink while washing it
Took the food off a temporary shelf I fixed up from old parts of something else and slid in the new one after taking off 3 stickers.
Parts Used:
-
Pat from Santa Rosa, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Light in the refrigerator didn't work
I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.
Parts Used:
-
Anthony from Fairport, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the part was loos
-
Deravine from New London, CT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!
Front wheel broke
Instructions came with the part I ordered and they were very easy to follow. Basically you have to remove the cardboard cover from the back. Then you remove the four screws at the bottom (2 front, 2 back) that hold the bottom plate on. My husband tilted frig and held it while I put a block(4" x 1/2") under the bottom outside frame (not the bottom plate). You can see a ridge on the frame which is where I placed the block. My husband braced the frig the whole time I did the repair just to ensure it didn't fall on me even though it was blocked. The bottom plate didn't slide back at first. I took a flat screw driver and hammer and slightly tapped the bottom plate through the screw hole that secures the bottom plate to the frame. I tapped 2 or 3 times...gently each tap...until the bottom plate dropped down. Which was the 1/2" noted in the instructions. I then was able to access the front wheel, remove the pin and replace with the new one. We replaced both front wheels so I did not replace the bottom plate until we replaced the second wheel. We removed the block and tilted the frig to the opposite side, blocked then I replaced the second wheel. Once that was done I removed the block, my husband let the frig down gently and I went to the back and tapped the bottom plate forward. It didn't quite want to go back in place but with patience it finally and then was able to put all screws back in. Donna
Parts Used:
-
Donna from Littleton, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Light switch went bad
Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th
Parts Used:
-
Joseph T. from Morgantown, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken door handle cap
-
Gaby from Boca Ration, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drawer rail in center cracked and no longer supporting drawers in center
-
Nicolette from Rochester, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
I broke the glass crisper shelf when I was cleaning it.
-
Jane from Llindsay, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Both light bulbs had been replaced, but lights did not turn on.
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Parts Used:
-
Richard from Arlington, MA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broke the arm off the food compartment rocker switch
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Parts Used:
-
David from St. Pete Beach, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the handle for the freezer compartment came off
unscrewed the broken part of the handle and put the new one on. It was easier than expected.
Parts Used:
-
jerry from Burnsville, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!