Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer was putting brown spots and tearing clothes.
My husband took the front panel off. We scaped the old seals off. Used the adhesive that came with the drum glide and replaced both parts. No more ripped and stained clothes, that easy!
I popped the top lid of the dryer which has hinges in the rear allowing it to be lifted. This exposes the drum. The front panel then can be detached using a nut driver and phillips screwdriver. The door shut off switch must be then removed so the front panel can be pulled away. I used an adjustable wrench to remove the lock nut. Once the front panel is clear of the drum, the felt and nylon glides are exposed. I removed the felt using a paint scraper, and cleaned the adhesive residue with lacquer thinner. The provided high temperature adhesive was then applied, I waited a minute per the directions, then applied the new felt and glides. The dryer reassembles in reverse of the above disassembly, making sure not to forget to reinstall the door switch. I plugged the dryer back in, and ran a load of laundry in quiet efficiency. Your part arrived quickly, the directions were good, and the dryer now works wonderfully.
Appearances can be deceiving.....while dis-assembly was a piece of cake; the problem turned out to be failed welds on the dryer drum. REMEMBER this before you make a parts decision. Examine the problem.FIRST! (this comeing from a guy who used to Manage an appliance repair shop WAY back in the day....DUH!)Solution?....new dryer; repair cost too high. None the less...at least I have a spare belt !!!
Popped the topped using a putty knife to free two clips in front. Remove two screws now accessible on the front inside panel. Remove two wires to door switch. Remove rear access door, two screws. Remove belt from tensioner in rear and remember or take picture of how it goes. Lift barrel slightly and pivot front panel out of the way. Lift barrel free from ball socket in rear. Lift out from front panel area. R & R kit and put back in reverse order.
Found the promblem as described at this site while looking for diagrams for the dyer. Repair went as described. Once I removed the old upper drum glide I used acetone to remove old glue. Cleaned up fast and easy. Once installed I let cure for about an hour and then reassembled. Let it cure for about an hour more and then I used the dyer. I could feel that the gap around the front of the drum was again narrow so that my finger tip would not slide into a grove. So far so good.
After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.
Removed two screws in the inside of the front after opening the top by releasing the two clips. Front comes off of bottom clips easily. Drum can be removed and repairs made. Takes less than 30 minutes Be sure to remove door switch wire & unplug unit first. Drum belt can be re-installed easily thru the back access panel.
drum turning out of balance, due to worn out drum glide top and bottom, and clothes being cougth beteween dryer frame and drum
I removed the top lid, then removed the front panel, to expose top and bottom drum glides attached to panel, then using a carpenter shisel, and cutting knive scraped away the old worn out glides, wiped clean with acetone the area were the new glides were being cemented. all of this thanks to couple of customers that had the same issues on their dryer, and documented step by step their own way to have this done, I just followed thru their experiences.
I followed the instructions on previous posts. The only problem I had was trying to remount the drum to the bearing unit which sits in the back of the driver. I just couldn't get the three holes lined up for the screws until I finally laid the dryer on its back, and then presto! - it went together in seconds.
This project probably took me longer than most people because I'm always looking things over and a little cautious in my work. I never realized how simple a dryer system is until I had dismantled this one. I spent $38 to fix my dryer rather than buy a new one. $10 of that was for the belt which I changed only because I was in there. Parts from partselect.com arrived 48 hours after ordering, and I used their basic shipping.
My dad and I followed the video instructions and it was easy! No more ear piercing noise! I did find that once we took the front of the dryer off there was a lot of lint! Never thought to clean the front of the dryer out! The video was a great way to see exactly what you needed to do, just follow what they say and you will have no problems!
The drum belt was making a squealing noise, and it looked frayed.
After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect PS this dryer is 23 years old.
Removed dryer top. Unscrewed the screw from each side inside the dryer the ones below the control panels. Don't unscrew those you will just have to put them back. Insert a flathead screw driver on the left side to loosen the front panel and slide it gently to the right. You can replace the drum glide without disconnecting any of the wires. Remove old drum glide and clean. Install new one and while the glue dries clean inside the dryer. Mine was very dirty!!!! Put everthing back and your ready to go. Don't forget to hook back the dryer vent. Thank you partselect my dryer is almost like new and is drying so much faster, no more noise and you have saved me lots of money.
