41748112700 Kenmore Washer - Instructions

Very easy to replace belt on this model, belt had spilt and the loose rubber was flopping around and dislodged plug from water pump. Washer would not start cycle, display showed (no spin). Removed back access panel with screwdriver. Spin the pulley and slip belt off pulleys. New belt is very tight but it will go on, no tension adjustment on this model. Thanks part select quick service will order again from this company.

screwed in the new legs and leveled it off again.

First,turned the power and water off. I disassembled the door lock and switch assembly by removing two screws from the rear of the top lid to gain access to the switch. Removed two screws from the switch assembly located in the front door latch area. With screws removed, I seperated the three terminal blocks and inspected the assembly for failure potential. Discovered a small crack in the switch housing which created error in relay function. Ordered the part and installed in reverse order of above. Realigned the door for proper closing, turned water and power on and did laundry all night to catch up!!!

I heard that the repair job was simple and the part was not expensive (whew!) The repair video on your website was MOST helpful and gave me confidence. At first I tried it exactly as the guy demonstrated and all went well removing the broken support. Installing the new one (on the right side) was impossible for me. I could not get good enough leverage to fully re-insert the lock pins and I was slicing up my arm on the sharp metal edges. I removed the 900+ screws (just kidding- but there were quite a few) from the back panel and could access the lock pins MUCH easier. All four for both shock absorbers snapped right in. Re-attaching the rubber vent hose involved a few cuss words but I got it back on correctly after taking a break. All is great with the little washing machine once again! Thank you for the installation video and amazingly fast shipping, wow.

The store I bought the washer from was going to charge $150 service call and over $60 for the part. I searched on the internet and found what i needed at partselect.com. The part was under $7 and the shipping cost more than the actual part. 2 screws, 1 screwdriver and it was fixed. Thanks!

I watched the u-tube video and followed what he did and it was fixed. Reason it took over 15 min I had to find the correct bit for the screw. I think your web site is great thanks

Open the door. Pull the clamp off of the boot (locate spring at bottom). Peel back the boot on the right side so that you can get to the door lock and switch assy. Remove the 2 screws in the front that hold in the door lock and switch assy. Remove the wires from the old assy. Transfer the wires to the new assy. Screw in the new assy. Refit the boot and clamp. give it a try.

The repair itself was simple; it was the original design of the washer itself that made it time-consuming, because of the tight spaces involved. Basically, all you have to do is remove 2 plastic pins, take out the broken part, make sure you have the new part facing the right way, and put the 2 plastic pins back in. Should take 2 minutes if there are not other machine parts in the way!

I unplugged it from the outlet, undid the two screws from the top, then slid it off, opened the door and undid the two screws from the door switch lifted it out relaced it with the new one, screwed it back into place, replaced the top, plugged it back in and away it went.
Garry

2 screws off and put new striker in and replaced the screws

My 10 yr old son removed the two screws, placed the new strike on, and screwed it back into place!! So easy a child did it!!

-Unplug machine and remove all water connections
-Remove back panel with power phillips screwdriver
-Removed some rectangular circuit box in the way of getting to one shock absorber (3 screws)
-Remove old shock absorbers with 1/2 inch socket (suggested in accompanying directions)- this took 2 minutes
-inserted new shocks as directed...this was the most difficult part, but used a hammer to bang into place.
-reinsert and screw down circuit box (or whatever it was)
-reattach back panel
-reestablish water hose connections
-plugged in and was in business
-had ordered a washer/dryer set for $1700 (at my parent's urging) and now can tell Sears to go pound sand!

PartSelect had the part in stock, shipped that day. The part was delivered the next day, my wife had it installed and working when I got home from work.

I had called a repair man; and fortunately he never returned my call. After reading many of the reviews involved with the same problem, and wanting to use my washer, I decided it was easy enough to give it a try. And so it was. 2 screws in back removed the cover; and 2 screws in the front of the washer permitted the removal of the affected part. Removed three "plugs" from old; put them on the new part; replaced it back in the washer, and replaced the two front screws, which held it in place. Replaced top, securing with the two screws. And surprise - surprise -- the washing machine was working again! Your reviews were so helpful and encouraging --- that this really old lady decided to try it --- and like they all said "It was really easy to fix."

After accidentally dropping a crystal clock (don't ask) near the open door of the front-loading washer, the plastic striker broke and couldn't be repaired. Without this part being functional, the washer won't start because the door can't be secured.

I ordered the new part, and it arrived quickly -- that's really the story here.

Replacing it meant removing two screws, pulling the damaged part off, slapping the new part in, and replacing the screws. My 4th grade daughter could have done this one -- wish they were all that easy!

I'm glad the part came so quickly. With a local supplier, it would have taken four more days.