Models > 3XWED5705SW2 > Instructions

3XWED5705SW2 Whirlpool Dryer - Instructions

All Instructions for the 3XWED5705SW2
646 - 652 of 652
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lint filter tore causing hang up with metal guide
Removed lint filter cover (3 screws). Removed old lint filter. Adjusted metal guide. Reinstalled lint filter cover (3 screws). Installed lint filter. Replacement filter is a like quality.
Parts Used:
Lint Filter
  • Mark from Layton, UT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
loss of heat
remove back of dryer and install new part
Parts Used:
Dryer Thermal Fuse
  • Timothy from Southamton, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would not run or start at all. Seemed like it had no power but the light still worked and it wasn't the breaker.
Took 12 screws off the back. One screw for the fuse. $9.32 and 30 minutes and we're back in business!
Parts Used:
Dryer Thermal Fuse
  • Joshua from Sturgeon Bay, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
lint filter gasket broken
replsce
Parts Used:
Lint Filter
  • Bob from Howell, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Gas burner would not fire.
First removed and checked the ignighter. It was fine. Next I located the schematic drawing and discovered that the burner, ignighter, and flame detector were all operated by one simple 110 volt circuit. This circuit did not power up when the dryer was cycled on. I pulled the dryer from the wall, removed the back panel, the vent etc. I then located the operating thermostat and the thermal fuze. The thermal fuze was open. (GOOD NEWS AN EASY FIX!!!) Thanks Guys
Parts Used:
Dryer Thermal Fuse
  • Leif from Plainfield, IL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
The control panel won't leave Casual load.
Well the video showed us taking off the back. Which wouldn't come off. Welded. Then we could not find the fuse in back of the unit or bottom. The second time we tried we found it in the front. We had to take off the front, bottom cover then we found the fuse. But, it didn't fix the problem. The unit is still on Casual load only. When we push the buttons the other lights light up but goes back to Casual. The unit is clear of lint and still drys but only at the Casual setting.
Parts Used:
Dryer Thermal Fuse
  • Ann from Cincinnati, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
door would not close catch fell within the door
Pushed the new catch in by hand. Working great.
Parts Used:
Door Catch Kit
  • Richard from Marmora, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 3XWED5705SW2
646 - 652 of 652
Back to Top