I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
I looked it up on the site per Refrigerator Model #. I wanted a confirmation from an expert at this site that I was ordering the right drawer. The part # the expert gave me was different than what I was going to order per my Model #. I'm really glad I waited for the expert reply and ordered that drawer. This is for a rental property, and we are a few hours away from the property. It was less than a minute to pull out the old crisper drawer and slide in the new. Thank You!!!!!
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Freezer was working but fridge was barely cooling. Look further into how to test thermostat.
I just replaced my defrost thermostat after using the place-in-ice-water method, and I think it may not have been necessary. My timeline: my fridge was not getting cold enough. I realized it the day before going on a trip. I vacuumed the (very dusty) coils at the bottom, and the next morning the fridge seemed colder, but I thought I should order parts just in case. I ordered a heater and a thermostat. The fridge seemed to be operating normally when I returned from my trip, but I had the parts, so I thought I'd go ahead and dismantle the freezer and test the existing parts. My intention was to return both parts if the old ones passed the tests. I opened up the back of the freezer and there was no ice on the fins. I thought, great, the existing heater works! I cut out the thermostat, placed it in ice water, and didn't get continuity. So I decided to go ahead and put in the new thermostat. Because I'm not experienced with using a multimeter, I thought I'd test the new thermostat to see how the test should work. To my surprise, the new thermostat also failed the test! Stumped, I thought I might as well install the new thermostat, since I had opened the package and couldn't return it. Further internet research suggests the place-in-ice-water method of testing is not adequate. One YouTube video by Parts Dr says to place the part in a working freezer. I froze my old thermostat and tested it; still no continuity. This thermostat may not be typical, though. The video discussed the temperature ratings on thermostats. The temperature rating on both (old and new) thermostats is L8.9-16.7C. That converts to 48-63 degrees fahrenheit, which obviously are not freezing temperatures. I'm not convinced I needed a new thermostat, but I trusted the videos I consulted earlier. I cleaned the fridge thoroughly, so at least now I have a nice clean fridge to show for my efforts.
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Original door gasket split from age, no longer sealing snugly to refrig.
Inserted scraper behind gasket breaking it free from door, permitting a hand hold. While putting tension on gasket, slid scraper around door gently removing old gasket. Replaced gasket starting at top gradually working around door. No need to remove door.
Gasket had several tears in it at the corners and was leaking air into the fresh food compartment
Removed the old gasket and ran the hard edged lip into the opening behind the door liner. Concerned that the gasket does not seem to be attaching itself to the door well. First put it on the side of the refigerator and it would not adhere enough to support itself. While it closes it just doesn't seem to attach with the magnets in the gasket. These magnetic strips have a weak magnet side and a strong magnet side. I wonder if they put the wrong side facing the door when they assembled it. Counter this with a new gasket for an upright freezer which was twice the length and attached itself firmly to the side wall of the freezer and did not slide down.