Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Auger blades separated from hub.
First I removed the screw holding the ice door shaft (at the rear of the ice container). Removed clip of which the screw was holding in place (no need to remove the clip from the shaft). Then I removed the front cover screws, separated front cover from ice container. Door shaft is removed with front cover assembly, no need to remove anything else from front cover. Pulled out auger shaft, removed circlip (snap ring) and washer from front of shaft. Used an adjustable wrench to remove plastic nut from front end of shaft. CAUTION - the plastic nut is reverse thread, make sure to turn it clockwise to loosen and remove. Pulled off broken auger then reassembled with new auger in the reverse order as previously described.
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!
i used the instructions that came with the part and it was really simple. thank you very much. it saved me a HUGH repair bill.we use alot of crushed ice and the part shipped in 2 days. thank you.C.D.L.
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Water line cracked at the water valve and was leaking
I took off the broken tube and attempted to order a new one with the confusing we sight at parts.com- after 3 attempts I finally got the right part with help from the operator at parts . Com( nice and helpful) but had to ship wrong parts ( the 2 wrong ones) back. The parts were of good quality and we're not hard to put on
SUPER EASY. I pulled out the ice bucket and confirmed the motor ran and the axel turned - however the coupling was missing. Ordered the coupling - pulled out the ice bucket, screwed on by hand with minimum effort, put ice bucket back and ice started coming out the door. It took less than 5 minutes and no tools required.
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Ice bin auger drum fins broke off from the main shaft,stopping the production of crushed ice.
Replaced the Ice Bin Auger,I ordered from PartSelect,which had much thicker housing and fins than the original .You remove the clip from the end of the shaft and a nylon nut which is a left hand which is opposite threads from most nuts.Its a good idea to take a picture of how the blades and spacers are ,because if not put back in the same direction their will be no crushed ice.It now works better and quiter than when it was new.