Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
washer wouldn't start
Parts Select is outstanding..They diagnosed the problem quickly..The part was sent within 2 days and we were washing laundry the 3rd afternoon...THANKS!!!!!!
Washer would stop during any cycle until lid is opened and closed.
Unplugged the washer. Removed the 2 screws on back of control panel. Pulled the control panel forward. Flipped the control panel back. Disconnected the cable from the lid switch. Removed the ground screw with a nut driver. Opened the washer lid. Removed the lid switch. Snapped the new lid switch into place. Closed the lid. Installed the ground screw. Installed the lid switch cable. Put the control panel back in place and pushed back. Installed the 2 rear screws into the control panel. Plugged the washer in.
I unplugged washer, then, removed the control panel with two screws on back, slid unit back and up. Unscrewed ground screw and unplugged harness, lifted lid and removed switch. In order to re-install lid switch, lid has to be in the up position, otherwise it will not fit properly. Reattach harness and ground screw, then control panel. Plug and go. My wife says that the washer works better than ever. Very easy! Saves money!
Machine had been walking and vibrating for a couple of months during the spin cycles.
Looked on line and found the cheapest repair for my symptoms seemed to be the tub wear pads. Disconnected the washer, tilted it to where I could inspect the pads and discovered one was missing. So ordered a set, (Only complaint was the shipping was as much as the part). Parts arrived in 2 Days (!). Tilted the washing machine again...reached up with a small flathead screw driver and pryed the old pads off...snapped the new ones on (takes a little pressure, so eat your wheeties)...and job done. Stood everything back up and re-connected hoses, drain and plug...Works like brand new...Unfortunately for the wife who thought she was going to get a new one....LOL
Luckily enough the washer shown in the demonstration is my exact model, which eliminated any variables I may have come across. The repair was relatively easy and probably could of been done in less time but I took every step slowly to avoid breaking something or leaving something unattached. For the money and time spent on this repair I would certainly recommend this for anyone with a similar issue. After taking the machine completely apart, i found that the suspension pads were still properly functioning. Since i had already purchased them with the tub wear pads, I changed them anyway. The trickiest part for me was pulling the outer tub out because the shaft on my unit was very rusted had a considerable amount of buildup on it. During this step I was very careful to remove all the build up because there is a single rubber seal between the center opening of the tub and the motor shaft. After I made sure the shaft was completely smooth and there were no protrusions I gently rocked the tub back and forth while applying pressure from the underside of the tub, all the while making sure that the seal didn't fold in on itself or stretch in any direction. Other than that, the repair went very quickly and easily . The spanner wrench is a must !!! I actually found it on amazon for about 6 dollars and I'm positive I will find another use for it somewhere down the road. I owe a big thank you to Steve. (the guy in the video) and everyone else from parts select for making laundry day in my house tolerable again !!!
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
Had issues with removing the inner tub
Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!
washer will not run through the cycles without stopping
removed the two screws that attached the top to the base. lean top back to access the lid switch. install the new one; best to have door open when installing. real easy repair that saved me mucho dinero.
Unplugged the washer and removed the two screws from the control panel. Raised the control panel and disconnected the wire connector that connected to the top.Then removed the two spring clips that hold the cabinet to the back of the washer. removed the cabinet from the washer that exposed the frame of the washer. I then replaced the broken spring by pushing the tub of the washer as far as it would go and replaced the suspension spring. Then i reinstalled the cabinet and control panel. Everything worked okay. ood as new.
The repair took about an hour. My wife told me the washer was so quite that she had to check and make sure it was running. It was like getting a new washer for less than 30 dollars. I've saved Part Select web site to my favorites and will use your company again.
Washer wasn't agitating or spinning. The timer was working, the motor coupler was intact so I figured I would start with the simplist thing and go from there. If all else failed, I was reacdy to buy a new washer.
Unplugged the washer and unscrewed hoses. Unscrewed the 2 screws on the back of the control panel and folding it up. Took off the 2 metal ties to get the cabinet off. Once off, I unscrewed the ground from the old Lid Switch and popped out. Put the new Lid Switch in, screwed the ground back in, replaced cabinet, clamps, put the control panel back in place and screwed the 2 screws on back of the control panel back in. Screwed the hoses back on, plugged the washer back in, everything works great again.
