3RAWZ480EMQ1 Whirlpool Dryer - Instructions

I first came to the internet to resolve what was wrong. After finding the video I thought was correct I started. I used my volt/ohm meter to check the thermal fuse as instructed on the video and that was the problem. I ordered the new thermal fuse from PartSelect late in the day and it was in my hands the next evening. With in 20 minutes the dryer was doing what it was suppose to do. The hardest part was getting the back cover of the crier off and that wasn't to bad.

Disconnected the power and duct from the dryer. Removed the back and top of the dryer by removing the 1/4" screws. Created slack in the belt by compressing the spring and moving the idler arm.Slid the belt off the pulley. Removed the tri-ring clip, slid the old pulley and gasket off. Cleaned and inspected the shaft and vacuumed the inside of the dryer. replaced the gasket, pulley and tri-ring clip. Replaced the top and back of the dryer. Connected duct and power.

Ordered the kit for my dryer. Popped off the front access panel and 4 screws later, dryer works perfectly. 28 dollars plus shipping and fixed. Great OEM parts and fast shipment from Peoria. Recommended.

I tried all standard tricks: checking circuitry, switches, etc. Then I read other submissions on your site, which suggested this thermal fuse was the culprit on almost 50% of cases. I got yours in 2 days, installed in no time, easy as pie. One caution: it will take an entire day if you forget to close the dryer door completely.

Went thru all the electrical connections, finally checked the thermal fuse. . It was the culprit. Next time I start there. Unlike older dryers, where one component gos such as the drum belt or the heating element and its only 2 years old. This thermal fuse shuts down the entire unit when it malfunctions

I took rear panel off with a nutdriver 8 screws.disconnected the 2 wires that went to thermal fuse and removed 1 screw holding it in place.replaced thermal fuse and reconnected wires and rear panel.turned dryer on. had heat. walk in the park!

Step 1: remove new latch from bag in which part comes. Step 2: push latch into hole where the other latch was. Step 3: enjoy having a dryer you dont have to hold closed with a folding chair.

Removed the top panel of the dryer via a couple of screws from the rear. Remove the rear panel swing it open light a door to the right, minding the electrical connections. Removed the belt from the pulley, removed the Tri-ring from the shaft and slid the pulley off of the shaft. The shaft was slightly rusted so I used a steel brush and brake cleaner to clean it up, placed the new gasket, pulley, and tri-ring on, replaced the belt, and put the panels back into place. As the dryer is about 7 years old, also removed the front lower panel and cleaned out unit which had quite a bit of accumulated dust and glitter especially in the vent lines. (3 girls live here). Pretty easy, most screws remove with just the one tool.

Could not be any easier. For less than $20 and 15 minutes time, I couldnt be happier.
All that was needed is a nutdriver to remove a 1/2 dozen screws to take the back panel off. Then a phillips screw driver to remove the thermal fuse. Unplug 2 wires and then attach them to the new fuse. Put it all back together and done!. Working dryer.
PS: I had enough gas line and ducting connected to the dryer ,so thatt I was able to get behind it with out removing them. This may have taken another 15 min. if I needed to do this and two adjustable wrenches.

I checked the thermal fuse for continuity and had none.ordered part arrived next day. I took a picture with phone to idenify wires. installed in a short time.dryer works like new

remove&replace

To make sure the dryer didn't die catastrophically, I checked to make sure the timer, the light, and the push to start start switch and the door switch were still working. After they were diagnosed to be working properly, I unplugged the dryer and pulled it back from the wall so I would have enough room to work behind it. The first item you will need is the wiring diagram. If you do not have one, one can be obtained online by using your dryer brand and model number. The next thing you will need is a quality digital multimeter that measures resistance or continuity. The last thing you will need is a 1/4" nutdriver. The first thing you will need to do is remove the exhaust tube from the back of the dryer. The second step is to remove a small black plate located near a green ground screw. The 3rd step is to remove the large black cover on the back of the dryer. Once this is removed, you will need to locate the thermal fuse. The thermal fuse is a small component that has 2 blue wires connected to it. It is located on the housing where the steam from your clothes leads to the exhaust port. The first thing you need to do is disconnect the 2 blue wires. Once the wires are disconnected, set the multimeter to resistance. The unit of resistance is ohms and the greek letter omega is used. The red lead of your multimeter goes one metal tabe of the fuse and the black lead goes on the other one. If the multimeter measures 0. L ohms, then the fuse is bad and needs to be replaced. If the multimeter reads 00.00 ohms then the fuse is good and you have another problem. I hope these instructions were useful.

there were 5 ,1/4 screws in the back panel . The heater box was right at the rear when the back was removed.. Replaced the two controls that were in the kit with a 1/4 nut driver. Checked the terminals for tightness and contact. No discoloration on contacts. Ran unit after reassembly for 20 min cycle to test ,Put into service

Watched several videos online and was suggested that the thermal fuse was bad, so i replaced it but no fix. So i checked the previews Q&A from other costumers and watched the videos on how to replace different parts. I first looked thru the peep hole on the bottom left part of the dryer and saw the igniter glow for about 10 sec every minute but no flame would start. So i replaced the igniter, the flame sensor, and the coils all at once. I know thats not the proper way to troubleshoot something but i was gonna take the drum out and everything so mind as well replace them all. Dryer works like new and dont have to listen to the wife complaint anymore!!!

Took the back cover off. Replaced fuse and put the cover back on. Worked great.