3NWTW5505SQ0 Whirlpool Washer - Instructions

Removed inner cap seal, agitator bolt and them removed agitator. Remove cam kit, installed new kit, reassembled. PS I am a retired appliance tech we ho has done this before.

it went very fast after watching the how to fix video

After about 4-5 years, the agitator cogs or "dogs" will wear out and cause the agitator to stop working-Simply pop the cap off of the top of the agitator with your hands by pulling upwards, remove the plastic cap at the bottom of the agitator-there are 2 plastic ears that you pull up on also with your hand, exposing a 1/2 locking nut. Use a socket and extention to unscrew the nut. Grab the bottom of the agitator with both hands and pull sharply upwards removing the entire assembly. Flip the assembly over to expose the four cogs. Replace with new, and reverse the procedure to reinstall the agitator

After watching the repair video by partselect.com I followed the directions exactly. It turned out to be a piece of cake. I found out that partselect.com has many, many do it your self repair videos on youtube.com. I intend to use them for future repairs. Thank you partselect.com.

Determined based on some Internet searches that the part that we needed was the motor coupling; washer would not spin or agitate. Once I figured out how to removed the cover (by the way, one of the guys at an appliance store told me how to do it), and reviewing the video on your website, I removed the two screws and four clips, dropped the motor, inserted the parts and put it back together - all in about 15 or 20 minutes. It was easy and clean and the washer worked again. Hopefully go for another 5-10 years. Thanks.

Followed website instructions, worked for a couple days, appears it needs clutch or possibly transmission(red oil present)

Pulled off clamps, removed 2 clips, pryed off pump from shaft, sanded shaft(as it had rust on it) put a dab of oil on shaft, installed pump, hold down clips and hose clamps.

Replaced the agitator cam kit due to noise, and bolt due to wear and corrosion. The repair itself was probably 15 minutes, but when you disassemble the agitator, you find a lot of cleaning needs to be done, which takes another 15min or so.

one thing that you do not need to do is to remove the pump from the motor, I tried to remove it as per the instructions but the pump cracked,remove both inlet and outlet hoses from the pump and remove the pump and motor together, don't try to take them apart, you don't need to, thanks

Did not know problem or how to access - thought the back came off washer. Typed in symptoms and it pretty much pinpointed the most likely cause. Watched video on how to take it apart (BTW the front and sides come off, NOT the back). Followed the guide, took motor off and sure enough one of the plastic couplers was cracked. Ordered from PartSelect and with regular shipping the cost was under $20 (ordered Tues. night, had it by Thurs.) Installed part - note as someone else said the new piece has metal inserts which make it really snug to go around the drive shaft, but the tip about using an oversized socket and some light taps to get it on worked liked a charm. Put it all back together (getting case back on was toughest part)and its been working fine for the last week - heavy & lite loads. Have to say was thinking the whole thing needed to be replaced (sound & age) but for $20 it was worth the shot...Glad i came here first!

Watched the repair video that came with receipt. Removed two screws from power head, folded out of the way. Removed two large clips holding outer shell on and removed outer shell. Tipped washer back towards wall. Removed two clips holding pump on to motor shaft. Removed both hose clamps, drained hoses onto towel. Aligned new pump onto shaft and did a reversed assembly of above items. Works great!

It was actually much easier than I expected. The worst part was dealing with the gear oil as I drained it to clean out the plastic pieces that came off the gear. To see how to fix things like this, I went to Google, enter my model and what the problem was and watched a repairman do it. It seemed easy and it was.

The clutch itself was fairly easy to repair. I did use some tips from youtube on disassambly, and the enclosed instructions helped to put the clutch in. There were 3 bolts I had to remove to take the drive assembly off, and 1 to pull the agitator out. And putting it back together it went in almost backwards. All in all, this is a fairly simple procedure in taking the time to complete the steps

Removed the upper sgitster by removing the center bolt to the bottom agitater. Manage to pull the cog housing apartfor inspection. left apart and ordered the new cogs. received the cogs within 30 hours and reassembled the unit and bolted it back to the main agitater. works perfect. great service. Thanks Ed PS Now my 97 year old mother in law can keep washing clothes. Shes happy again.

Remove the sides of the washer, motor ran but nothing moved, closer look found drive coupling broke (10 years and it made of plastic) Order a new part from you, arrived very quickly. Install the part 10 min. later it was running.