3LGR5436EQ1 Whirlpool Dryer - Instructions

took the top and front off the dryer and had to route the new belt around the drum and through the pulleys, it was really easy and a heck of a lot cheaper then buying a new dryer

Called PartSelect, gave them the make and model number of the dryer and told them I needed a new belt for it. They gave me a price including shipment (under $20.00). I oreder the new belt and it arrived within a week. I also got an e-mail from PartSelect with a video showing how to replace the belt. This was very helpful. I was able to watch the video, take the dryer apart, replace the belt (after a few tries), and put the dryer back together. Problem solved! Thanks PartSelect.

very easy had to do some rewirng.who ever had it before me bypassed the fuse and several other things.

Just like the video. Disconnect the lint shute. Pop the top lose. Disconnect the door switch. I actually took the hooks off an removed the entire lid. Took the two screws out and removed the front panel. (The OEM idler was a teflon half-moon so I think the abrasion was what caused the belt to fail.) Put the belt around the drum. Rolled the drum to check the seal overlap was proper. Installed the idler and wrapped the belt around the motor shaft. Put it back together. Would have been a little easier with a helper.

Found an instructional, easy to follow video by PartSelect online. It was helpful to know what tools I needed before beginning the job. I first purchased only the belt. After taking the dryer apart, I saw the idler had also broke. It was very helpful that the parts arrived quickly. The video was the the greatest tool for doing this repair myself!!!!

i took the back apart to find the problem, then i went online to findout how tomremove the blower wheel, just googled it. Easy!Took itnall apart, just had a bit of trouble getting the wheel off, was on there very very tight. Ordered it through you, easy, and very very quick, received it in a day. I got an email explaining the reassembly process. Easy. Just follow it to a t and you will be fine. As a woman, this was an easy fix.

Tools and materials:

#2 Philips head screw driver
Standard flat-tip screw driver
1/4" nut driver or ratchet
1/4" drive sockets: 1/4, 5/16
Something 3-4 inches thick to wedge under drum for support (i.e. scrap 4x4, soap bottle, books)

Replacement Procedures:

1. Unplug dryer from wall outlet
2. Pull out lint screen
3. Remove 2 Philips screws attaching lint trap to dryer top
4. Lift hinged dryer top panel near front and lean it back on wall. You may need to pry between side panels and top with flat-tip screw driver to get it started.
5. Disconnect plug from dryer door switch near front
6. Remove two 1/4" and two 5/16" hex screws inside front panel near top.
7. Open dryer door and lift front panel straight up to disengage tabs from slots near bottom of front panel.
8. While supporting drum with one hand, lift front panel and set aside with other hand.
9. Slip replacement belt around drum with ribs facing drum and position it where old belt left its mark.
10. Wedge something under drum to support it while installing the belt.
11. Re-position tensioner in two slots in bottom panel just in front of motor. On my model the bend in the spring will be on the right side with the idler pulley to the left, when viewed from the front.
12. Ensuring the belt isn't twisted, thread a small loop of it through the opening in the tensioner just below the pulley.
13. With the left hand, push against the tensioner spring while working the loop over the drive pulley.
14. While supporting drum with one hand, remove whatever you put under the drum to support it.
15. Replace front panel by aligning the slots with the tabs near the bottom and lowering it into place.
16. Carefully slip the drum opening over the flange on the front panel and replace hex screws.
17. Slowly roll the drum in one direction or the other until the belt aligns and centers itself.
18. Re-connect the plug for the dryer door switch.
19. Lower the dryer top and press until it snaps back into place.
20. Replace philips screws to secure lint trap and replace lint screen.
21. Plug dryer back into wall outlet, close door, set to dry, and press start.

Took screwdriver popped out old latch in cabnet. Took pliers popped out latch out of door. Snaped new latch parts back in.

Removed rear panel screws carefully removed panel with out disconnecting wire harness located thermal fuse removed 2 screws removed the 2 wires with needle nose pliers put new thermal fuse in connected the 2 wires carefully put panel back on and tightened screws turned on power and start got heat problem fixed

Watched the videos for unusual noise... they are great and saved me time with advice how to open the machine from top and front and install belt on tension wheel. Lower roller bad, replaced both. Opted to also order and replace the belt and rear seal upon inspection. Time spent would have been 30 minutes or less but rear seal replacement requires time to clean off old seal adhesive and glue on new one. Take your time with rear seal replacement it takes longer than I thought but worth it. The labor involved to replace the seal alone would have been more than the dryer cost new. Also- I ordered parts at 2pm std shipping option and got them THE NEXT DAY less than 24 hrs later. May not be typical depending on your location but I was amazed. I have been fixing all my own appliances for years first time customer with Parts Select. Oh and EACH of the 3 parts ordered were 10$ less EACH than my local parts guys. WOW

I diagnosed the problem using the web page. It said that 60% of the people with my problem bought the Thermal Fuse. I unplugged the dryer AND cut the power at the fuse box. I used a screwdriver to remove the vent hose, a nutdriver to remove the back of the machine. The thermal fuse was right there. Removed the old one with a screwdriver, unplugged the wires from the old one and snapped on new one, and screwed it back in. Re-installed the back of the dryer and the vent hose and Whoila! It works like a champ.

I watched the video and did the repair myself. My husband, who works in maintenance, was IMPRESSED! Yay! Thank You!!!! Love you guys! I am forwarding your website to my children!

Repair was very easy simply used a screwdriver to remove the cracked old latch and used my fingers to insert my new latch.

Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!

Removed front and back covers on dryer, screws on top and down one side to spread cabinet to remove drum,removed blower cover to get access to shaft nut on that side. The other is accessible. I found that both shafts can bethe longer of the two that were sent. The shorter shaft is too short and needed to be modified to let the roller come outward to lay in the grove in the drum. I will get a longer shaft and replace it.