3LGR5434BW1 Whirlpool Dryer - Instructions

I lifted the top of the dryer. I unhooked the hangers from the door and took it off. I pulled the drum out, took the broken belt off, slid the new one around the outside middle of the drum, turning the rib side of the belt out,and ran the belt through the pulley attached to the bottom base of the dryer (tension pulley, right hand side), slid the drum back inside the dryer frame, reattached the door, closed and snapped the dryer lid and it worked great!!

Installed new filter and it is working great!!!

Your customer service was great, but your video wasn't particularly helpful because of the extreme age of my dryer. For one thing, with these really old dryers, you don't have to slide the drum out at all; you just unscrew the front panel and slip the belt in that way. The printed diagram that came with the belt helped me figure how the belt slips through the pulley assembly, but the drawing could have been more clear. In spite of my bickering, I probably saved $50 fixing it myself.

Disconnect electric power, the top & cabinet are connected by 2 reusable locks about 4 inches from each front corner, use a thin flat putty knife or similar object, push inward on a lock while lifting gently on the front of the top piece, then let the top rest against the wall. ( a wire on each end of a safety switch for the dryer door may need disconnected) Remove a screw from each front corner of the cabinet, then pull upward on the loose front panel to access the drive motor, remove old belt. install new belt by lifting the front of the drum just high enough to allow the new belt, place groves of belt against the drum and around the motor pulley and belt tensioner, re-install cabinet front, (re-connect safety switch wires) return top and push down at cabinet locks.

I checked the thermal fuse for continuity and had none.ordered part arrived next day. I took a picture with phone to idenify wires. installed in a short time.dryer works like new

It was really easy I watched your video on how to do it the video went step by step and was very helpful

First I watched a instruction video online.. It made the job easy. I have done it before but I did not remember exactly how to proceed, After watching the video i knew exactly what screws needed to be removed and what tool I needed for each step. Anybody sees the video before tackling this job, they can't go wrong.

followed video on line

To make sure the dryer didn't die catastrophically, I checked to make sure the timer, the light, and the push to start start switch and the door switch were still working. After they were diagnosed to be working properly, I unplugged the dryer and pulled it back from the wall so I would have enough room to work behind it. The first item you will need is the wiring diagram. If you do not have one, one can be obtained online by using your dryer brand and model number. The next thing you will need is a quality digital multimeter that measures resistance or continuity. The last thing you will need is a 1/4" nutdriver. The first thing you will need to do is remove the exhaust tube from the back of the dryer. The second step is to remove a small black plate located near a green ground screw. The 3rd step is to remove the large black cover on the back of the dryer. Once this is removed, you will need to locate the thermal fuse. The thermal fuse is a small component that has 2 blue wires connected to it. It is located on the housing where the steam from your clothes leads to the exhaust port. The first thing you need to do is disconnect the 2 blue wires. Once the wires are disconnected, set the multimeter to resistance. The unit of resistance is ohms and the greek letter omega is used. The red lead of your multimeter goes one metal tabe of the fuse and the black lead goes on the other one. If the multimeter measures 0. L ohms, then the fuse is bad and needs to be replaced. If the multimeter reads 00.00 ohms then the fuse is good and you have another problem. I hope these instructions were useful.

Open the top and replaced the switch bracket with the actuator lever then inserted new door catch.

Ordered the part, called a friend that is a LP worker. He came over and in less than 15 mins had the new orface and regulator plunger installed and another 10 mins to install new flex pipe and shut off valve and it works great. It was really easy I watched him do it and could of done it myself if I did not have a friend that could do it.

Watch the video you sent me, and every thing fell into place

Initially confused by instructions provided in that it stated to loosen a brass coupler. Disconnected power. Removed front bottom panel. Disconnected both leads to ingiter. Removed the 2 screws holding igniter bracket in place. Carefully slid igniter and bracket forward and removed from dryer. Removed screw holding ingiter and replaced with new. Reinstalled in reverse.

Removed top and front of dryer. Removed drum. Removed old rollers from spindles. Installed new rollers and new retainer triangles. Replaced drum. Re-installed front and top.

I made it very difficult. I didn't research the repair. My back is old. It's easier if you just You Tube a video. The top roller you have to take drum completely out. The bottom one, The one that failed for me, you can actually do it without taking anything apart. Access it at bottom back, two holes. I do not have small hands, it would have been easier. Channel Locks inside, 9/16th socket outside. That will loosen main axle. Then use short screwdriver or socket driver on small bracket connected to bottom of unit. Mine had one screw holding it in. Easy bottom fix. I don't really recommend replacing top till it needs it. You can only buy them by the pair too. You will be ready when time comes. I found top roller didn't actually need replacing, did it cause I had it all apart. Don't fix if not broke, right? Trust, BUT, Verify. Smaller hands, would have helped me. All I got.