3LG5701XPW0 Whirlpool Dryer - Instructions

I followed the basic steps in the video for the dryer door switch replacement. My dryer is much older but everything in the video was basically the same. It was a very easy repair. I have kept this dryer running for 26 of the 27 years of our marriage.

It was not hard at all. I got the parts the next day.

Verified that the heater element was working; drum and contents were getting hot. Could hear the thermostat clicking on/off as the element started to glow. Drum stayed very steamy the entire time; consistent with no airflow. Fan motor was running, dryer vent/line were clear. Verified cold (not hot) air from the external vent. Seals had degraded to the point that the fan was not drawing air from the drum, but from inside the dryer cabinet at the lower seal (by the fan blades); hot air was escaping from the upper seal and was causing the dryer cabinet to get unusually hot. Installed these 2 seals, and the dryer is working perfectly now.

TURN OFF POWER TO DRYER............................. Pay attention to where everything is as you take it apart, so it can be put back the same way. Take out the two screws by the lint screen. Use flat tip screwdriver between space in front of top to help lift top. Use rag on tip of screwdriver so as not to scratch it. Take out two screws inside the front panel at the top. One on each side. Unhook the switch wiring. Lift up the front panel to take off. The tub will be loose, so it can be taken out to inspect other components. Some call the tub a drum. Be sure to see how the belt tensioner is attached, so it can be put back on the same way, if it comes loose. It is under the tub. Take out old belt. Put new belt around tub. Make sure the tub sets on the two rollers in the back of dryer. While holding tub, put the belt around the grooved pulley on the motor. Grooves are face down against the tub. Feed belt through the tensioner. Put the bottom of front in on the tabs. Be sure belt is still in place around pulley and tensioner etc. Hold tub through front door and close front. Put the two screws back in on each side. Close top and put the two screws in at the lint screen. Done. Turn power back on. Turn on dryer to see if it operates properly. If not, check out your repair to see if everything is connected properly.

pull out lint screen, removed 2 screws. lifted top up. removed 2 screws from the front,disconnected wiring harness. removed the drum and belt. located and removed the igniter, sensor, and coil valves. replaced all with new parts. reassembled. now it heats up. i believe that i only needed the coil valves. coil valves not shown on parts list, i purchased later. everything was very accessible with the drum removed.

Used PartSelect instructions for routing belt & a customer's valuable guidance.

I removed screws for the lint screen - TOP. Pry up top with screw driver. Disconnected inside top front 2 screws, removed door control wires, white and blue. Lift off front of dryer. Tip dryer back about 40 degrees against wall. Remove warn belt (not broken). Relocate idler bracket on the cabinet base, follow diagram which comes with the belt package. Be very careful that the belt is NOT on the side of the idler roller. I had to do this install a second time, because I had it wrong the first time. Even though I've done this repair 5 or 6 times, there's always a first time GOOF. Not really a hard job.

Threw away the printed instructions and followed the Part Select video ,featuring Steve...

Well my husband did the install and he said it was very easy??

Ordered thermal fuse and cycling thermostat

always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James

Instructions are available from other web sites. A few tips from me. Tape the dryer doors shut. When you remove the springs it falls open. Remember to just loosen the hex screws at the bottom of the front panel, it has slots and just lifts off of them. To easily remove the clips holding the motor bearings use a dull chisel or small pry bar on the outside half loop and tap the end with a hammer while lightly forcing it out.

Watched a you tube video on replacing a dryer belt for a whirlpool dryer. Perfect instructions. Dryer is working great.Thank you

I'm a 66 year old lady with no repair experience at all!! I found the part I needed on Parts Select, which I ordered and received in less than 4 days. I watched the video that you've posted on your website which shows in great detail how to do this repair. It looked like a simple fix and it was!! I highly reccomend Parts Select!! Took my granddaughter(held flashlight) and myself less than 30 minutes to do the repair!!!

video on your website made it super easy