3LG5701XKW0 Whirlpool Dryer - Instructions

Remove two screws on top holding the filter frame.Use flat screwdriver to snap top at front off front panel.Swing top up and secure it against wall or tie in place. Remove screws holding front panel and kick panel to side panels.Did'nt remove back panel.Remove drive belt from pully wheel and then use belt to lift out drum.Use open end wrench on motor pully at rear and I used a socket set on the front of motor,Push down on wrench,counter clockwise,and hold the front pully from moving mine came right off. My dryer is over 10 yrs so the electric conection was changed but the instruction sheet explained how to change the wires,just follow the wire color,easy.

I watched the video on this site and it went exactly as described, fixed it and it sounds like a new dryer. Was going to junk it, glad I didn't!

My 40-ish year old Whirlpool dryer needed its lint filter replaced. You guys had the replacement! Fast shipping and even faster switching out the filter. Thank you PartSelect.

I won't tell you how we did it, but I'll tell you the right way. Unplug. Remove the exhaust tubing attached to back of dryer. Pry the top up from the front and lean it against the wall. Un plug the wires attached to the front panel (remember where they go) Remove screws at top sides of front panel. "lift up" and remove. Close top. Lay machine on its back. We used a couple of 2x4's to lay it on so as not to crush the vest collar. Clean it out, including lint filter. The new belt wraps around the drum, you will see the channel about midway on drum. Feel behind the motor on the lower right side. There is a shaft with a channel for the belt. Immediately next to that is another pulley type arm with another channel for the belt. This arm moves stiffly and puts tension on the belt when installed correctly. Look at the diagram included with the new belt which shows the path of the belt. Wrap the belt, ridges against the drum and then around the motor shaft. At this point you have to physically pull the last arm out to allow the belt to wrap around the channel provided. If the belt is not twisted , the job is done. Turn the drum with your hands to make sure it is turning properly. Replace the front panel, plug in the electricals, replace the screws making sure the drum is properly centered. Stand up the dryer. Plug in and turn on dryer to make sure everything is right. Replace the exhaust tubing and set into place. Sounds like a lot of steps but I have described the whole process for you beginners. The rest of you will know already. Good Luck . Oh by the way we are 69 and 71. If we can do it, so can you

I watched the video several times to make sure I got it right. The first thing that was very helpful was how to disassemble the top cover and front panel using a putty knife to disengage the detents. With the cover off I could acccess the belt and idler pulley. Replacing the belt was fairly easy as long as you note the way it threads through the idler pulley and drive pulley. I thought the video was excellent. It took me right to the problem and the fix. As a bonus the price for the belt was much lower from Parts Supply then from Sears. I've recommended this site to several others.

Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

Removed the broken actuator and replaced with the new one. The time to replace the dryer door switch actuator took about 5 minutes.By the way, I purchased the dryer in 1965 and it works as if it was brand new. Thank you Kenmore for a lifetime dryer.

Just as in the video. Sounds like new. Had to feel it to make sure it was running.

Removed the front cover of the dryer as well as the lint holder and framework to gain access to the thermal fuse which is behind it and mounted on the discharge side of lint fan. replaced fuse but the dryer still wouldn't heat each time the ignitor glowed. Also then replaced the solenoid (both of them) and this fixd the problem as it has been good for a week now. The solenoid issue is not easy to conclusively identify as an issue as it is inconsistent in operation.

two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clothes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened

This was replace the old worn out limt filter with a new limt filter effort. Not a difficult repair. I would call it a remove and replace job.

removed old lint filter by hand and replaced with new one.

took the top and front off the dryer and had to route the new belt around the drum and through the pulleys, it was really easy and a heck of a lot cheaper then buying a new dryer

Called PartSelect, gave them the make and model number of the dryer and told them I needed a new belt for it. They gave me a price including shipment (under $20.00). I oreder the new belt and it arrived within a week. I also got an e-mail from PartSelect with a video showing how to replace the belt. This was very helpful. I was able to watch the video, take the dryer apart, replace the belt (after a few tries), and put the dryer back together. Problem solved! Thanks PartSelect.

Just like the video. Disconnect the lint shute. Pop the top lose. Disconnect the door switch. I actually took the hooks off an removed the entire lid. Took the two screws out and removed the front panel. (The OEM idler was a teflon half-moon so I think the abrasion was what caused the belt to fail.) Put the belt around the drum. Rolled the drum to check the seal overlap was proper. Installed the idler and wrapped the belt around the motor shaft. Put it back together. Would have been a little easier with a helper.