3LER5434BW1 Whirlpool Dryer - Instructions

unplug unit ,remove back cover six screws, slide off two wires on thermal fuse, remove one screw remove and replace fuse, reattach wires replace back cover

New lint trap was in good shape and ready to slide into its proper place. Easily done. Works well.

Our make/model was not on the online instruction, but it was similar. Ours had a glass (plastic)front window in the door. To remove the top catch you had to take out the top four screws that hold the door together (philips head screws) allowing you to pull back the gray plastic strip to access the top latch, then replace it like in the online directions using a needle nose pliers. The bottom catch, once the two remaining the screws were out gives you access to the bottom catch. Remove it with the pliers and snap the new ones into place. You can completely take out the window when you replace the bottom latch if you want.

Just pulled the old parts out on door latch and put the new ones in. Thanks Parts Select for your prompt response and easy process for order and shipment.

I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

Easy to follow videos on your site made this repair a breeze. I ended up having to replace the high temp cutoff as well but for 60 bux my dryer works like new. The repair man wanted $100 just to come look at it. Could not have done of without the easy to follow video.

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

The video you had of my dryer was different then my dryer and the pulley was in the middle of the bottom and the motor and fan were in front of it. I had to replace the belt without being able to see what I was doing. I couldn't get it at first then realized there was tension on the pulley wheel and had to pull it towards the other wheel in order to get the belt on there. Once I pulled the wheel it went on really easy. My first time working on a dryer but I knew I could do it myself.

instructions were clear and repair was easy

Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history

The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

went online to whirlpool typed in my problem and. was directed me to Partselect which said it was thermal fuse and had picture where it was located and how to replace,easy as that.thank you PartSelect.Tim

First I watched Partselect's wonderful videos on what could cause the dryer from having to use multiple cycles to dry and the parts involved. I then took the back of the dryer off and tested all three parts with a multi-meter to determine which part had no resistance. The thermal fuse did not register any thing, so I ordered the part and a few days later put it in. The dryer dries in just one cycle saving on the cost of repair and electric bill. Partselect.com is my first go to sight for any repair. They make it so simple and comprehensive that any one can do the repair. I then used duct tape to make a secure connection to the duct pipe in order for it to properly vent to the outside.

Previously I had repaired two washing machines and now a dryer, which is why my mom nick named me Josephine. So ladies you can make the repairs as well.

Had a lot of trouble getting front panel off. Check You Tube for directions. Checked heating coils and thermostats and found they were OK. Cleaned lint from fan and replaced thermostats although they may not have needed it (thermal cut-off kit). Put panel back and it works. See YouTube to see how to check coil and thermostats. They may check but if something is wrong it is either them or the control board. Thermal Cut-Off Kit is much cheaper.