3LE5710XMW1 Whirlpool Dryer - Instructions

Replaced both drum wheels and belt and cleaned lint out of entire unit. Works perfect again. Great fast parts with super on line instruction if you need it.

Followed general instructions from your you-tube video. It was much easier than expected. We didn't know if it was belt or rollers, turned out to be roller, but since we bought both we replaced both.

I researched the issue, found a video and ordered the belt, which came in 2 days. It was inexpensive, and I had my dryer back and running in less than 3 days. I did get my son to help me as it might not be that easy with just 1 person (to hold the drum in place while putting the front back on). Great service and great information on how to do the repair.

When we ordered the part we watched the video, to see what needed to be done and both my husband and I got the dryer all ready for install before part came so when the Ups delivery came it took all of 10 min to get it back up and running! Thank you so much for having the details and a video made thing go so well! Sincerely Dawn

I loved the demo video on how to do the repair-it was very helpful. My dryer was different than the one on the video, and I had to make adjustments ( I had self tightening screws on the top and bottom of the front panel and then I stripped the screws)I did this by myself and I had to prop up the drum AND the front panel with items in laundry room.) That's why it took me longer than demo (also had to run to hardware store to get screws). Felt great to accomplish this by myself. Thanks!

The door handle fit prefectly.....

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

I know now that I did not have to get in the back of the machine. Only lift top remove two screws for the front and lift off.The most diffcult was determing how the idler and belt went in but if you hold it in position it becomes to you. Thanks for all your help you run a good ship.

I unplugged the dryer then loosened the screws on the top and inside front, took the front off, I didn't need to unplugged the socket wiring attached to the door. Removed the drum (it came right off) wrapped the new belt around the drum, fed the belt through the tension flange and looped it over the pulley. Then rotated the drum a few times by hand to line everything up then put everything back together. It works fine now.

Before placing your order remove the motor. At the rear of the motor is a plastic nut which is how the fan is attached. Mine was stuck and needed to be removed with a cutoff wheel from the back side of the dryer. This delayed the project several more days as I had already received the motor before figuring out the fan was stuck.

Watched the repair video on part-select. Pulled the top of the dryer up after removing the lint trap screws.removed screws at top, inside both sides and then lifted front off. Slipped belt over drum and ran through tensioner and around motor shaft. Put dryer back together in reverse order. Simple.

The only added thing to know is how to remove the lower kick plate. This is not on later models. Other wise all the directions are the same as for models with a full solid front panel. Immediately below the dryer door, at the right and left end, there is a plastic clip similar to the one holding the top panel to the vertical side panels. Insert a flat screw driver or putty knife releasing the plastic clip. This will allow the kick plate to fall forward on rings at the bottom of the plate. Release springs at either side of the dryer door (reattach later using pliers or a hook). Unscrew the nut screws at either side of the dryer door. Remove the door panel and the kick plate and put to one side. Reverse to reattach. I replaced the wheel tension part and the belt at the same time. I put the dryer on its back to install the wheel, belt and tension part. I used strips of scotch tape to hold the belt in place at the top and sides of the drum, while I looped the belt on the tension wheel and the driver wheel. I used the bungee cord to hold the top in place while I put the whole drier on it back. Good luck and have a vacuum handy to suck out years of dangerous lint....

removed two screws from filter chute,raised top of dryer and removed front panel,lifted drum out,replace both rollers,replaced drum,reset belt tensioner replace front panel,lowered top,put screws back into filter chute.

Remove the back panel, then remove the housing around the blower, just slide the housing of to the side, you don't have to take it completly of the machine. Remove the top, and remove the front until you can get to the blower motor. Cut the blower wheel plastic down to the metal nut with a fine blade in a recipricating saw, used a bi-directional broken stud remover socket on the nut that was at the center of the blower wheel and large slip joint plyer on the other end of the shaft. Replace the wheel and put back together. It took about as much time to gather up the tools as it did to fix it.,

Exactly as described by the video.