3LCGD9100WQ0 Whirlpool Dryer - Instructions

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.

Just like the video, just followed the video
Thanks,

Ezee pezee lemon squeezee.

all that was required was to push the catch into the slot notools needed.

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.

My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.

I had two dryers, one was gas and the other was electric. The electric stopped heating. So I rolled out the gas dryer, but it was setup for natural gas and at this location, I only have propane. So I changed the jets to work with propane, in the process I broke the igniter, so I replaced that and that made the propane one work. Armed with the knowledge from that job, I took the electric dryer apart located the thermostat and replaced that and low and behold I have two working dryers. One for now and one for an emergency. I only have four screws left over!!!! Jim Cooke

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexible dryer tube since the old one had a few holes. It works perfectly again.