3ED27DQXAW00 Whirlpool Refrigerator - Instructions

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

First, although I was SURE I knew what to do, I watched the repair video. I used needle nose pliers to push broken support into wall since I could not pull it out. Selected correct wall fixture, spread holder pins, and snapped into wall opening. Couldn't have been easier!!! Very useful site.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

I took the upper three screws pull the door up and then removed the broker part in the bottom of door by removing one screw. Install new part and put door back securing it by the three screws on the top of regrigerator. Very easy

Easy job due to great instruction video by PartSelect.

Before I ordered, I followed the great video to disassemble the unit. That's when I realized I only needed to buy the drum. Five days later, I had the part. I thought I remembered how to reassemble it, but I ended up needing to watch the video again. It wasn't difficult, but you must get all the bits back in the same order!! Once that was dine, it all went together easily. Thank you! I'm so impressed with this site that I posted on Facebook about it so my friends can also save big bucks doing simple repairs themselves.

Removed all the crisper shelves, twisted out the old supports, twisted in the new ones and cleaned the bottom of fridge while pans were removed.

Fridge side: Remove all door bins. Close the door. Pry off top hinge cap. Using 5/16" nut driver, remove three screws. Remove top hinge by lifting it up. Place pad on floor to prevent marring. Hold door at sides. Open door halfway and lift it up and off the bottom hinge. Do not let door fall! Set door on pad. The lower and upper cams are different; do not mix them up (check the parts list). Remove the old lower cam from the hinge (on fridge) and install new lower cam with new screw. Remove the old upper cam from the bottom of door and install new one with shoulder screw provided. If the old cam does not have the shim, do not use the shim from kit. The kit has extra parts and screws. Lift up the door and set it on the lower hinge pin and close it. Reinstall the upper hinge and shim loosely with the three screws. Adjust the door before tightening the screws. Check that the gasket is compressed evenly all around. Open and close the door. The door should close easily. If the door does not close easily, remove it again and smear some Vaseline on the lower hinge pin and cam. Replace the door and put a little Vaseline on the upper hinge pin before inserting it into the door. Finally, replace the upper hinge cap and replace the door bins. Repeat procedure for freezer side. This fridge does not have water/ice dispenser in the door.

removed cover unbolted thermo an replaced no big deal

The reason it took me longer than what should have been a 15 minute repair is due to the fact that I could not figure out how the shaft came apart. I found an instructional video on Parts Select website that showed me that the shaft was held together by a reverse treaded, round nylon nut on the very front of the shaft. Just use a pair of pliers to grasp the nut and rotate it clockwise, after that you just need to lay the parts out in order as they come off the shaft so you can put it back together again.

Simply follow the video instructions. Involves the removal of nine screws. to remove the old plastic sleeve cut the tube near the old thermostat and it slides of easily. Apply dish or hand washing soup to the new tube when putting the plastic sleeve onto the new probe. The hardest part is getting the end of the probe coiled to the right shape. Hey,` if I can do it with a broken collar bone, anybody should be able to do it.

Read the instructions, watched the video and followed the very clear instructions and lay out.

Repaired it using the video that you sent through email. Thank goodness for the video or would still be trying to fix it!

Very simple and straight forward

When I ordered the new auger drum from this website, I noticed a video that explained how to install the item. When I received the new drum, I went to the website and found the video. All I did was to watch the video and do what the repairman did. I did get a little confused when I noticed that the auger in the video was metal, and mine was plastic. However, upon removing the pieces as shown in the video, it became clear that the new auger drum would fit the same way the broken one had fit. After that, it was a snap to put the pieces back together.