Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Porcelan Electric Burner Plug broke
The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.
burners would not come on without moving them around
took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing
When The Burner Started To Heat (Front) And Then Put The Rice Bag On The Burner. Then The Plastic Bag Began To Burn And The Bag Of Rice Began To Pour Over The Burner. Someone Tried To Clean Up On The Burner But The Burner With Plastic And Hard To Clean The Plastic Off From The Burner.
Just pull the old out from the stove and put new one on the stove and then tested the burner that is working fine. Thank you very much for order the part. Have a great day.
Oven would not heat up properly to set temperature
The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced with a new one.
Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.
Slid oven out from counters. On each side there are 3 screws on the front and three screws on the back holding the side piece on. Once off, the spring was very easy to get at and replace. I had only one broken, but replaced both anyways. I think it took longer to clean the sides of the oven that haven't been touched in years than to replace the springs. This job was very simple and easy.
surface burner stopped working. Was not heating up.
The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)
I needed to replace to two 8* drip bowls on the kitchen range
(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.
Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!
Burner no longer connected with electric power source
I had determined that the the burner itself was no longer capable of connecting because when I removed another burner and inserted it, it worked just fine. Also, the defective burner had not worked when inserted into another outlet. I was delighted to be able to purchase a replacement so quickly and easily on my own, without having to call a repair person or seek a retail outlet.
1. Removed racks 2. Removed two screws holding in the bake element. 3. Gently pulled out the element exposing the two wires connected to it. 4. The two wires were held by a clip connection. 5. Removed the wire clips holding the wires. 6. Attached the clips to the new element and re-installed the element. New problem: The element did not heat up. A repairman informed me that the selector switch was damaged during the burnout- that switch was no longer manufactured and was discontinued. Whirlpool company was checked and indicated that there was a new part # 7403P023-60 but that was discontinued too. I was able to get the element working by moving the selector switch to the "Bake" position and then moving the switch about 1/4" in the clockwise direction. The element heated and the oven works at least for now as I search for a replacement part. PartSelect was an invaluable aid and helpful all along the process.