Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Difficulty in removing the old switch
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.
The part arrived It said to warm it to take out wrinkles but not even a picture of how to take off the old or put on the new. Everything on the internet in general about gaskets explained about unscrewing the old gasket but I couldn't find any screws. The user feedback mentioned no tools and that was our only clue and the only reason we finally succeeded. We looked at it repeatedly over 5 days. Pulled and pushed and could not figure out how it was attached or how to unattach without breaking things. I finally got out a screw driver and tried to pry it off. An hour later I got a corner piece started to come off. We pulled all the way around and got it off easily once started. We again struggled to put the new one on. Couldn't really tell what area of the gasket fit back into the crease. It kept falling off. Finally we pushed the correct edge of the gasket into the crease. VERY difficult. Fat edge fits into skinny crease. Took a lot more strength than expected so it didn't seem right but it was. Took a while and a lot of strength to work the corners and sides in. Eventually got the whole thing on. A picture and 4 sentences would have been a big help. Wouldn't try it again. To anyone else...No screws. Use a lot of strength. I hope someone publishes a picture for you.
I first unscrewed the broken right rail from the back piece and replaced with the new rail. Did the same for the left piece side. Attaching to the front rail was challenging because I took a while to figure out how to remove the cover (where the pictures of the vegetables/fruits are). But if you just get a narrow flat-head screwdriver under there, it just pries off. Then you can get to the little screw that attaches the side rails to the front piece.
The refigerator not getting cold and the freezer coils where a solid block of ice while the refrigerator never turned off.
After finding your web site, the description of my problem was pretty clearly referenced as to what parts where the likely problem. When I received the parts it was only a matter of unplugging the refrigerator, removing the cover in the freezer and cutting and stripping the two color coded wires for the thermostat and wire nutting the wires and putting wire tape on them. Then put the coil cover back on. Then in the refrigerator section, remove the controls cover and then take the controls compartment loose and unfasten the old defrost control, and install the new one. Then put every thing back in place. Plug the refrigerator back up and set the temperature to medium.
Icemaker waterline leaking inside by the grommet where the water line comes in the refrigerator . First removed the water line from grommet . Then removed grommet by hand from the fridge. Last, reversed prodedure.
Left Vegetable Drawer Slide Rail was broken thus making it impossible for the Crisper Drawers to function properly.
I removed the Glass Shelf on top of the Vegetable Drawer assembly, unfastened the front rail from the broken slide rail and removed the entire assembly. I cleaned the parts and then installed the new rail. I placed the drawers in the repaired assembly and placed in the refridgerator. It really went well. I didn't need the other parts order. I only had them just in case they were needed.
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Bracket was broken near the front mounting location causing the rt drawer
First i removed everything from the bottom shelf, removed the glass, then removed the entire bracket assembly. Then removed the front metal strip to expose the front mounting screw, then removed the rear screw. Installed the new part and reversed the procedure.
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.