Models > 36343484201 > Instructions

36343484201 Kenmore Cooktop - Instructions

All Instructions for the 36343484201
76 - 85 of 85
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
old,burned pans
replaced
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • James from Apache Junction, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
heating element would not heat to red hot.
unplugged and installed
Parts Used:
Surface Element - 8 Inch - 2350W
  • David from El Paso, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Rusted out burnner bolws
Remove old burnner bolws and install new ones
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • charles from ft.pierce, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
dirty bowls
used my hands to remove heating element, then remove drip bowls, then install new bowls, then install heating elements, done!!!!!
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Richard from Bainbridge, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Drip bowls were rusty and not original GE. Small burners never fit quite right and rocked unevenly.
Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in opening and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Ian from Casselberry, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
needed new drip bowls for stovetop GE
removed the burners and dropped the drip bowls in. Very easy to do,
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Patricia from Centereach, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
the center of the element had broken
just pulled the old one out and replaced with new one. very easy
Parts Used:
Surface Element - 6 Inch - 240V
  • Betty from Fayetteville, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
stained drip bowls
unplugged burners replaced drip bowls plugged in burners
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Sunny from Salt Lake City, UT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Needed to replace drip bowls
Husband just snapped in place in about 8 seconds! Thanks for the fast delivery and pleasant staff assistant.
Parts Used:
Drip Bowl - 8 Inch
  • Gloria from Dallas, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
welded supports for the surface elements were broken
unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.
Parts Used:
Surface Element - 6 Inch - 240V
  • Thomas from Montgomery,, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 36343484201
76 - 85 of 85
Back to Top