Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door gasket broken up
It took considerable time to remove the door and take it completely apart so the gasket could be inserted, and time again to reassemble properly. The gasket (though the no. was confirmed before ordering) was 3" too short so I had to cut some off the old gasket to make do (not entirely effectively).
While i was inserting the new lp,gas orriface to the right rear burner tube I dropped the oriface.Without looking i popped the top of the burner unit, like most older type stoves, and thats when i ran into my problem. I realized the burner tube assemblies are attached by 3 screws to the top cover.Not attached to the cabinet as the older models, Basically cracked both front aluminum tubes trying to retrieve the dropped oriface. so i had to replace the burner tube units, which involved removing 3 screws, and loosing up and removal of the nut to the main gas tube. extremely easy repair, next time i`ll try to remember look before i leap,total time to (r+r)burner tubes about 20 minutes.Parts select pulled me out of the fire on this one, great staff and service, with quick delivery.
Here's how I fixed my problem. I took the aluminum cover, the part that sits over the jet & the igniter, which simply comes off. It's the part that the igniter discharges to. I took this cover off & using a pencil I scratched the lead of the pencil into the area which is around the igniter. I made sure to cover the area with as much lead as I could get on it. You need to make sure that you do this to all four burners. The only care you need to take, is not to block the gas jet which is in the igniter recess. It's been about 3 weeks since I added this & the burners click loudly & have lit without a problem. It appears that the aluminum may develop a coating on it of some kind which is highly resistive.
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
I was surprised to find that the 2 screws holding on the plastic end caps were not philips. it looked like an allen wrench deal but that didn't work. Turned out that I had to buy a hex tool. Looked kinda like a swiss army knife but had allen wrench like hex tools in various sizes. By then I was determined to finish the job even if it meant buying a tool I'd never use again. The job took about five minutes once I had the right tool. The stove looks normal now. The stove looks brand new but for some reason there were cracks in the end caps where the screw hole were.
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
While I was waiting on another part to arrive, I decided it would be a good time to do a thorough cleaning. When I lifted the top of the range, I lifted it to far and cracked both front burner tubes. The top of the range should not be lifted more than 4 inches without removing the 3 screws that hold each burner in place. When the new lines came in, I removed both front burners, knobs, and then removed the front plate behind the knobs using a Phillips screwdriver. The screws are located on the bottom of the plate. Using my adjustable wrench I replaced the lines. Then I CAREFULLY bent the gas tubes and remounted the burners. Over all an easy install. Just be careful, the gas tubes are aluminum and will break very easy. This is the second time I used PartSelect, and I am very satisfied.
burner tubes both had pin holes in them and the ignighter didnt work
This was a real easy job and a success,of course any repair i do on a gas appliance and when finished It doesnt blow up i consider a success. Thank you,David Williams
Wife broke gas lines when trying to clean under hood
Removed old line with wrench and attached new line to gas valve first. Then lowered hood to the stop and attached gas line to burners.........very easy and works fine now.
Turned off the gas. Disconnected gas inlet, burner supply line and oven supply line from regulator. Unscrewed regulator from its bracket. Replaced with new regulator in reverse order and added teflon tape suitable for gas lines to all threads.
Unfortunately, the regulator was not the cause of the problem and the oven still does not prehead - acts exactly the same.
Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked open!)