36275324100 Kenmore Range - Instructions

Removed the old glowbar's two screws. Didn't take a mental photo of its proper placcement (or a real one, which would've been smart). Removed screws holding 1) a heat protection plate, and 2) wire harness plate. Installed the new glowbar, hopefully, the right way - with its heat-plate facing the gasline of the over/broiler. Reinstalled the heat protection plate and wire harness plate. Hasn't blown up yet!

1. Removed oven door..
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.

Tested for power to the igniter, (had power) so I knew it must have been the igniter that had failed. Removed two screws that held the shield in place, remove two screws that hold the igniter and disconnect the plug form the igniter, replace with new igniter.

I let my brother do the actual installation but it only look about 15 min. I did look at the website of the appliance manufacturer first and then came to this website. The cost of the part I needed was almost half as much as the other site. When I saw that someone with the same oven model number and had the same problem and was able to fix it, I decided to order here. It came quickly and my oven now works.

In general, other repair stories on this site collectively give a good description of the repair process. My words concern the decision that has to be made as to which element is bad - igniter or gas valve. To reach a conclusion about this question, I was comforted by the fact that I could measure the AC electric current through the gas valve which then let me decide that my problem was in the igniter. Since the circuit is a simple series with three elements, thermostat, igniter, and valve and the resistance of the valve unit was 1.0 to 1.2 ohms (per GE range equipment instruction which came with the range) by measuring the AC volts across the valve, I found (by dividing the volts AC across the gas valve (2.3 volts) by the resistance of the valve mechanism (1.0 ohms) that my old igniter was only supplying 2.3 AC amperes (instruction sheet states 2.9 amps. is needed to actuate the valve and further while heating of the oven is occurring the valve AC current will raise to 3.2 to 3.6 amps.). At 2.3 amps. the igniter will glow at a yellow color but will not actuate the valve. When you replace the old igniter with a new one you will enjoy to measure voltage across the gas valve once again and discover that the voltage rises to 2.9 volts and that the gas turns on and the heater tube gas is ignited.

In my case it was the lower burner so I unplugged oven and turned gas off.
Then I removed the bottom drawer, and the lower burner cover.
Next unplug Oven Igniter, found where drawer existed.
Removed 2 screws attaching Igniter using nutdriver
Placed new Igniter on
Plug Igniter in and tested oven
Replace burner cover and drawer


This was much easier then what I went through with a repair man the first time around. These Igniter are designed for certain model stoves and are not interchangable with other model stoves!!!

I first took out the screw which held the bottom plate for the oven. then took the screws off the igniter unhooked the wires , took the new igniter hooked up the wires then put the screws back in put the bottom plate back in and turned the oven on to test it and it worked great.

Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.

Remove the draw from the stove. Then unscrew two Phillips Head screws ( one on each side). Remove the old gliders. Slip in the new gliders. Screw the two phillis head screws back in. Make sure when you put the drawer back in the stove that you lift the front of the drawer up enough that the lower portion of the new glider is engaged on the side rail of the oven drawer space.

I replaced the oven igniter, discovered the floor of the oven had rusted through, so I replaced that as well. The burner on top of the stove would not light as it was designed, and because the 12 screws that hold the range top and burners in place were rusted in place I ended up buying a new range because removing the screws on the burners proved impossible, even when I tried to drill them out with a lefthanded screw removal tool. I should have just kept lighting the burner that would not light, with a match. That was a repair too far, that forced me to buy a new GE Range and throw this one in the trash. The igniter, oven floor replacement was easy. The burner igniter after 18 years proved impossible. .I installed the 18 yr. old burner grates on the new range, but the drip pans would not fit the new stove. New GE Range instructions were near useless. Do Not trust them, especially the Orifice change details NG to LPG.

Replaced the flat style oven igniter. First, I watched the video on your web site, and used it as a reference to make the repair. I did remove the oven door tho, as it made it easier to complete the work, the video didn't show the door being removed. The video was very helpful.

the instructions given for this part were not 100 % accurate, our oven door required multiple, dis assembly and was unable to complete the task, local handy men refused to come to assist since the job was already started, it appears I will now need to buy a new oven , I was disapointed in the help because had we known we had the more diffcilult oven, would not have attempted, I did give the correct model and serial number to the person when discussing this part

The oven would not light and the clock was out. The surface burners worked.

Replaced the stoves control board using the instructions provided on this site. I would just like to add that you should unplug the stove before beginning and also know how to turn off the gas should anything happen while pulling the stove away from the wall to get to the rear to remove the control board.

It was an easy process which took about 30 minutes. A lot of that was cleaning behind the stove. The control board perfectly matched the one on my 1998 stove so I guess it is good for another 20 years.

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

Most videos show getting to the igniter module from the front when in fact with this older GE its accessed through the back left corner from the backside. So easy, a few screws and I was in. Quick change out and all worked well again.