I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.
After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.
The repair was just a matter of sliding the old one out and plugging the new one in. The ease of use of this website was wonderful. Super fast shipment. Im very pleased.
The burner was shortening out and would work sometime. The first time I replace the burner but the new one shorted out quickly.
I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.
Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.
Turned off the power. Pull the range away from the wall and removed the eight screws holding the cover in place. Carefully pulled the wires off the old switch. Removed the old switch and replaced it with the new. Put all the wires on and replaced the back cover and was done. Burner works fine. This part replaces a lot of different number switches.
surface burner stopped working. Was not heating up.
The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)
I needed to replace to two 8* drip bowls on the kitchen range
(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.
Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!
1. Removed racks 2. Removed two screws holding in the bake element. 3. Gently pulled out the element exposing the two wires connected to it. 4. The two wires were held by a clip connection. 5. Removed the wire clips holding the wires. 6. Attached the clips to the new element and re-installed the element. New problem: The element did not heat up. A repairman informed me that the selector switch was damaged during the burnout- that switch was no longer manufactured and was discontinued. Whirlpool company was checked and indicated that there was a new part # 7403P023-60 but that was discontinued too. I was able to get the element working by moving the selector switch to the "Bake" position and then moving the switch about 1/4" in the clockwise direction. The element heated and the oven works at least for now as I search for a replacement part. PartSelect was an invaluable aid and helpful all along the process.