31315VBV Magic Chef Range - Instructions

turned the old burner to the left and lifted it out. unpluged the wires with a screwdriver pluged the wires into the new burner and putit back on the stove and turned it to the right

I followed the instructions on this website. Luckily a friend showed me where the sensor was located and from there, it was a breeze. Removed six screws on the back oven panel, removed two screws inside of the oven, took the old sensor out and put the new sensor in. Voila - works great. I can't tell you how much I appreciate Parts Select and the feedback and help from the customers. I've been out of work for almost two years and when I called my repair guy, he said it could be the computer and that would be expensive. That's when I searched on line and found Parts Select. I would have never even attempted this on my own if it weren't for you and it was so simple. Next time anything goes wrong with an appliance, I'll be contacting you first! Thank you.

in and out in 15 min ,is easy when part fit.

Took my right hand twisted burner off unplug wires pluged them back into new burner and put burner back on done 3 mins tops.

I was a little intimadated as I hadn't tried any type of repair like this before. My oven is almost 20 years old so the ignitor was hard wired; there wasn't any plug. I wasn't able to remove the burner assembly so I had to do all my work inside the oven. I had to cut off the plug and hard wire it to the oven. It works great now. All I noticed was that the oven temperature is higher than what I set it at.

Took the old igniter out by taken some screws from the top had to remove the bottom cover underneath then had to cut one of the wire on the igniter put the new one end put the screws back in plug in the oven back iand then check to see that the oven will get hot it did the repair went well.

Removed the racks and bottom tray in the oven. Unplugged the old igniter and plugged the new one in.

Great.... thanks!

I found that the igniter would glow but the burner would not light. I was not sure what part I needed so I went searching the internet and fortunately found "Part Select". Your trouble shooting guide not only told me what part I should buy but demonstrated how to do the repair with a very helpful video. Thank you PartSelect for the the excellent customer service! Mike Dicken Wrightwood CA

I tried to take it out from the inside as the vidio shows. But it would not come out far enough. I pulled out the stove and removed back sheet metal panel. Unpluged the electric, Unhooked the temp sensor,pulled it out from the oven side. Put the new one through the hole,and rehooked it up. And got to clean up the dust and my missing oatmeal I spilled a while back. Turned it on. Checked it with a spare temp gage. Works so far.

Very easy repair. Removed door, shelves and bottom cover over igniter. Removed two screws holding igniter, unplugged wire and removed igniter. re-installed all parts.

Since I had never done anything like this, I watched your video twice. The oven door and racks came out easily. The wire connectors had burned, fusing the plastic parts. I cut them off and spent more time looking for a wire stripper than on the repair. The new igniter looked just like my 1993 oven part. Works great. Be SURE to unplug and turn off gas before starting!

Ordered the part from this site. It arrived In the time thy said it would. Removed old oven igniter and replaced with new one. Removal of screws and old igniter. Replaced with new igniter and put screws back nd it was working again

We received the burners we ordered in timely manner, and it was very easy to install. Just unhook the old burners and drop the new ones in and connect.

Called a repairman who came to the house to check the oven and stated it could be one of 3 things but he was not sure what it would be. Stated 2 of the parts would be $200 and the third would be a rebuilt part costing $400. At his suggestion we ordered a new oven. However, before it came in the old oven started working so we cancelled the order. When it would not light a few weeks later, we went to the Maytag website and was directed to PartSelect. We found the list of problems, located the part we needed and received it within 2 days. We watched the video on the PartSelect site on how to install it. We paid the repairman $80 for showing up and he had no idea what to repair. We paid $42.28 total to repair it ourselves. Thank you!! We would recommend your services to anyone before calling for professional help!!