Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The oven igniter lit up, but did not trigger the gas.
This website easily diagnosed the probable problem. We ordered the suggested part and my husband replaced it, despite a slightly eroded, rusted screw that was stubborn to remove, in about 20 minutes. The oven is working perfectly. With tax we spent about 50 bucks. I was sure we needed a new oven. We, ironically, celebrated by going out to dinner!
Oven would take 3 min. too lite,would not hold temp,sometimes go up too 350* then down too 250* maybe not relite @ all.
It took all of 10 mins. Open oven door slightly lift to remove.took out shelves and bottom of oven,lift at back to remove.Two screws hold the Igniter, was able to pull the connector into the oven to change. Oven works great!
First i removed the two screws that hold the element in place. I then pulled the wire out of the hole and disconected the plug. then plug in the new one, put the two screws back in, and checked it to see if it worked,It worked like a new one! So as my reward my wife baked me cookies!
This is simple for most people - unscrew and remove the bottom oven floor pan. There is the igniter, removed with two screws with a 1/4 nutdriver. However, my problem was that when I unclipped the old igniter, I dropped the over part of the connection, it fell down the hole, through the insulation, to the bottom of the stove where the wiring is. I had to pull out the stove to get to the connection, push it back up the hole to the oven, then install the igniter. My advice: do no lose your grip on the oven wire whatever you do. Otherwise, it was a snap, even for a klutz.
I tried to get black drip pans to replace the ones I had which were well in need of changing. They no longer make the black so I found the silver ones on your site and thought for the price I would try them. They are wonderful and very reasonably priced. I ended up buying a spare set for later. Thank you for such great products and prices.
Oven Burner Would Not Start Fifty Percent Of The Time.
My top burners and broiler were working fine so I knew it was not a gas pressure issue,after reading other peoples oven issues I felt comfortable that my problem was the oven igniter, the igniter was only building about 50 to 75 percent of the normal glow/heat needed, thereby not creating enough heat to trip the sensor that opens the oven burner gas valve. 2 Screws hold a drip pan which after removed allow access to the igniter. 2 Screws hold the igniter in. You need to access the rear of the stove to plug in the new igniter connector at a 1 screw access panel in the center of the back of stove. My oven has been working great since the repair. I would recomend partselect anytime, I ordered the wrong igniter, the diagram is confusing so be carefull , and had to send it back , I got my refund in less than a week. Good luck from beautiful western new york state.
After reading about my problem, I determined it was the igniter. I immediately ordered one. It came two days later. I took the bottom drawer out and removed the shield. To get to the plug wires, I unplugged the old igniter. I used my power nut driver to take off two threaded screws so igniter could be removed. I then pulled the old igniter out. Plugged new one in and reversed process to install new one. I installed it when I got home from work in less than 30 minutes. all is well. We were looking at buying a new stove for $700.00. I fixed it for less than $60.00. Thanks
removed oven door, removed all shelving....unplugged the electrical cord........unsrewed the igniter(2 screws)removed some of the insulation on back of oven that was covering the wire and plug......disconnected the wire plug...........reversed the process and 15 minutes later I was done............the oven works great.......the new igniter arrived 2 days after I ordered it. thanks
Ignitor glows but oven doesn't ignite or ignites then turns off.
1.) Remove door from hinges (open slightly and pull up). 2.) Remove racks. 3.) Remove oven floor to expose burner. 4.) Remove wing-nut and burner cover. 5.) Remove two ignitor mounting screws. 6.) Pull wires and connector through back wall. 7.) Connect new ignitor and mount to burner. 8.) Replace components in reverse order.
My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.
Oven would't heat up/ wouldn't heat to proper temperature
I opened the door partway to remove the door. Then I removed the bottom heat shield plate by pulling it towards me and lifting it up. I removed the two screws holding on the igniter, then with the the disconnect removed the old ignitor. I plugged in the new ignitor, replaced the screws, replaced the heat shield, replaced the oven door, and was done in ten minutes.
Replacing the vertical mount igniter was very simple. Remove 2 srews and one plug. I did pull out the oven to unplug te igniter. The process could not be easier.
