Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bad oven ignitor
A friend replaced the new ignitor with the old one...very simple job.
I would like to comment on how fast the service was from when I ordered the part online to 3 business days later when the part arrived....very happy about how easy it was to order part and that the part was in stock and delivered so quickly. Thank you very much !! I will recommend Part Select to a friend that frequently orders parts.
Removed lower burner covers and fan cover to access igniter. Unscrewed igniter and pulled out as far as possible. Marked both wires and snipped them. Twisted on wires from new igniter and mounted igniter. Pulled excess wire thru to back of oven and reassembled covers from first step. Last step was to explain to wife that she needs clean in there MUCH better.
1. Unplugged unit and shut gas off. 2. Removed the oven door(2screws). 3. Removed the oven floor(3screws). 4. Removed heat dispersion plate(1bolt). 5. Removed faulty igniter(2screws). 6. Labeled and spliced wires. 7. Connected new igniter. 8. Installed all previously removed parts. 9. Restored power and gas to unit and oven fired up in a matter of seconds.....Thanks
suspected oven ignitor,went to partselect website and saw others had same concern and ignitor was the failed part.ignitor was not getting white hot just orange-not enough voltage going to the gas valve to open it.ordered and replaced ignitor.repair took about 20 minuets-oven repaired.
oven whouldn't come on or if it did it whould take along time to come on and stop after awhile
pulled bottom door out as far as you can. lift out broiler tray and the tray under that. to get the door completely out. on each side of the rail holding the door from come out push in the tap on each side and pull the door all the way out and off. reach inside and take out two nuts holding the old igniter and cut the two wires and remove it stripe about 1/4 in of the wire. attache the wire from the new igniter. hold them two and use the white cap and twist it on the two wires and do the same to the other two wires. Bolt the igniter back on with the two bolts and your done. When you turn on the oven the igniter will click and turn on. it will be alot brighter then the old one and the oven will start pretty fast.
I replaced both gas valve and igniter. I removed oven door and bottom of oven for easy access to both. The door slid off easy and the bottom was held by two thumb screws. I removed the gas flare for easy access to igniter & valve. I then removed the igniter & valve using nutdriver, phillips screwdriver and adj wrench. I then followed simple instructions supplied for wire connect on igniter and valve. It was a very easy job for a 25 yr old stove. I made the mistake of ordering only the valve and ordered the igniter later. Having both new parts causes the oven to light in about 30 seconds. Im glad I found partselect online. Nh, westerville, oh
Figured out which part we needed by reading about others problems; Followed instructions & Presto = oven heats!!!! Didn't have any problems removing or replacing part.
First, I read all the instrutions that came with my replacement part from Parts Select thoroughly (twice) then follewed them like an experienced surgeon. I removed the lower drawr after turning off the gas and unplugging the stove and then took out the bottom panels inside the oven to expose the screws holding the ignitor coil. Removed it, then cnnected the new one to the existing wires as they were in the stove and the drawing in the instructions, then replaced everything in the reverse of them coming apart. Plugged it back in, turned the gas back on and now it,ll bake things again. YEAH!! Parts Select!!!
I just sent in a generic description of my problem and a couple of ideas on what it might be. Within 2 days an online repair person answered me back with the solution. I ordered the part and 2 days later I was back in business and baking cookies.
Gas oven would take forever to light and would not relight if cooking temp was reduced
1. Unplugged power cord. 2. Removed warming drawer and oven shelves and lower plate 3. Removed old wirenuts from back of warming draw space (awkward to reach in to the back). 4. Removed 2 screws holding ignitor in oven - screws in poor shape and were not reuseable. 5. Found next size up sheetmetal screws and installed new ignitor. 6. Ran wires down adjacent to gas feed into warming drawer space. 7. Connected with wirenuts supplied with ignitor. 8. Replaced everything. 9. Tested oven and ate some tasty blueberry muffins.
There was a glow in the oven but the oven wouldn't heat up
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconected the two wires. Take the old element out, and attach the new one. Assemble in reverse order.