30-2603-23 ((01)) Tappan Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ignitor burnt out
I removed the broiler burner assembly held in by 5 screws across the inside top of the oven, as I removed the assembly the igniter slid out from the back of the oven and was attached to the assembly with a cannon plug, I disconnected the cannon plug and removed the whole assembly out of the oven and replaced the igniter which was attached by two screws and reassembled in the oven. Where I live in remote Alaska calling a repair technician is not an option, either figure it out or have a new appliance barged in.
Parts Used:
-
Gregg from Naukati, AK
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
14 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler igniter not glowing
1) Turn off the gas and disconnect the power
2) Remove oven door. There requires that you remove the two square drive (SD) bolts on the inside, partially close the door and lift it off the hinges.
3) Remove the grills.
4) At the back remove the rear shield (aluminum panel held by 2 SD sheet metal screws.
5) this exposes the broiler igniter and its two wires. If its been replaced in past, there should be two porcelain screw-on wire connectors. Undo the connectors by turning them counter-clockwise. With a volt-ohmmeter, measure the resistance across the igniter. If its open circuited, its broken. If not, then its in the circuit board, and this help stop here. If this is the original igniter, it ends in a plastic connector. Disconnect by pulling it apart from its mating plug and again, check the continuity of the igniter. If its defective, reconnect the connector and cut each wire on the igniter side. Strip back about 1/2 inch of insulation on each lead.
6) inside the oven, using the SD driver, remove the 4 screw securing the broiler burner from the roof of the oven. The burner can now be removed, pulling the burner away from the gas jet on the right.
7) The igniter is now exposed and can be remove by removing the two SD drive screws.
8) Replace with the new igniter, being careful not to touch the black element, and feeding the wires though the rear oven wall.
9)Reverse the above dissembly procedure.
10) Broil the sausages.
2) Remove oven door. There requires that you remove the two square drive (SD) bolts on the inside, partially close the door and lift it off the hinges.
3) Remove the grills.
4) At the back remove the rear shield (aluminum panel held by 2 SD sheet metal screws.
5) this exposes the broiler igniter and its two wires. If its been replaced in past, there should be two porcelain screw-on wire connectors. Undo the connectors by turning them counter-clockwise. With a volt-ohmmeter, measure the resistance across the igniter. If its open circuited, its broken. If not, then its in the circuit board, and this help stop here. If this is the original igniter, it ends in a plastic connector. Disconnect by pulling it apart from its mating plug and again, check the continuity of the igniter. If its defective, reconnect the connector and cut each wire on the igniter side. Strip back about 1/2 inch of insulation on each lead.
6) inside the oven, using the SD driver, remove the 4 screw securing the broiler burner from the roof of the oven. The burner can now be removed, pulling the burner away from the gas jet on the right.
7) The igniter is now exposed and can be remove by removing the two SD drive screws.
8) Replace with the new igniter, being careful not to touch the black element, and feeding the wires though the rear oven wall.
9)Reverse the above dissembly procedure.
10) Broil the sausages.
Parts Used:
-
Steven from Silver Spring, MD
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver
11 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grates were old and rusted and scratching the bottom of my pots
I threw the old ones out and replaced them with the new ones. It was a no-brainer :) The parts arrived super fast. Great, no hassle service.
Parts Used:
-
Sue Z from Los Angeles, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
igniter failed
take broiler oven door off. replaced the wire clip on one side of the two wire harness. on the other side, I clipped the other wire, used the wire sripper too strip each side of the wires and used the ceramic wire nut that came with the kit. I did not have to remove any part of the stove for this job. twisted the wire nut on, and my job was done ! replaced the broiler door and you finally are able to cook your famous meat loaf ! Mike
Parts Used:
-
Michael from Chaska, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
4 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rusted out front burner
-
Dennis from GLEN MILLS, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't light.
My existing igniter glowed but the oven still did not light. I determined it was too weak to activate the gas valve so I replaced it. Simple fix, four screws, wire nutted the two leads. Fired right up, took about 30 minutes to replace.
Parts Used:
-
Thomas from ELMIRA, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Actually, the igniter I purchased is to be used on my furnace.
I have a Nordine model G2RC-105C19 LPG gas furnace. It was installed in 1995. The igniter went out and my son who was a propane gas appliance service tech installed one that was for our gas range. He said they were the same with the exception of a metal mounting plate on the stove igniter. Once the plate was removed, the igniter fit perfectly on the furnace. As a side note, the one I just bought from PartSelect was less expensive than one for the furnace.
Parts Used:
-
Lester from Waynesville, MO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
1 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas burner went bad
I had the old burner already out, so all I had to do was insert tab into slot and then fasten with screw. Tried the burner and it worked, I just had to adjust the amount of air it received. Very satisfied with product and quick delivery.
Parts Used:
-
Kenneth from Hickman, NE
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broiler wouldnt fire
followed the excellent posted instructions. The hardest part was cleaning up the area behind the stove that hadn't seen daylight in years.
Parts Used:
-
max from antioch, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!