30-2272-23-04 Tappan Range - Instructions

Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.

I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.

1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.

Snapped it on!

First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two screws on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.

pulled off old knob and put on new one. This knob fits a Tappan S110 gas range

I removed the oven floor and subfloor. I detached the old ignighter leaving the wires still attached. I then attached the new ignighter and fed each of the two new wires down through the bottom of the oven floor following the same path of the old wires which were still attached. I attached the new wires one at a time to make sure I connected them to the right place. Then, I pulled out the old igniter. I then attached the oven floors and turned the oven on which now works. The tough part is pulling the oven out from the wall to disconnect the power and turn off the gas. I did not remove the oven door.

replaced it

Removed the broiler compartment door by depressing the slide stops inward and pulling the door off. Turned off the breaker to the oven. Used a nut driver to remove the old ignitor ( 2 screws ). Cut the wires off the old ignitor close to the porclin. Measured the new ignitor wires to match up with the old ignitor wires and cut them. Stripped 3/8 " off ends of newely cut wires of the ignitor and used the supplied wire nuts to secure them together. Replaced the new ignitor with the 2 screws. Turned on the oven and a cooking I went.

I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

I saw a chart of the oven door at site after I finally got the model number. I actually thought I had ordered the wrong part, third door in was last pane I thought, but actually this is inner most oven door, glass panel four. I had to find a correct screw diver which took awhile. I thought I didn't have the strength to turn the necessary screws, but easily could with correct screw driver. I followed other stories about removing handle, spring loaded door, so be careful it pops apart. A bit tricky to put back together, cause you have to hold door together against spring when you put cap on and door handle. Remove handle, remove top plastic cap. Will see screws holding glass and aluminum shield in place. Remove shield, need to remove screws holding glass two panes with holder. Shield pulls back and this glass just drops in. Reassemble door.

Replaced the flat style oven igniter. Turn off gas and unplug oven. Removed the broiler drawer, cut wires, unscrewed oven igniter (using a small/medium adjustable wrench), connected wires, fastened new igniter to bracket, spliced wire, twisted together, plugged oven back in, turned gas on, turned on oven after a few minutes...worked great.

took the old igniter out and swapped the connectors onto the new one. Kept the connectors close to the connector end to prevent them from being to close to the ovens heat.

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconected the two wires. Take the old element out, and attach the new one. Assemble in reverse order.

It was pretty much a plug in. My husband had it done in a few minutes. I want to thank you for your great service with receiving the part.
The oven is working great and now I am back to baking.
Thanks for everything
Christy