30-2239-00-01 Tappan Range - Instructions

First, I took out the racks. Then I removed the bottom cover of the stove. (This was in place by two screws that I used my drill & socket set.) Next, remove burner cover by a socket set. Finally, in the corner was a metal cover that covered part of the electrical connections. I then used the screw driver to undo the screws that attached the igniter to the oven. I undid one wire connection, and wired it with the new one on the igniter. (To make sure I wired it correctly.) Then I undid the other wire, and connected it with the new wire (using the new wiring nuts provided.) Done! Now just put all the parts back together.

After reading the input of others on your site I ordered the igniter. Within a short time it was installed and the oven works fine. Thanks for the help, jc

First i disconected the plug went right where the trouble was.removed the two screws and the safe plate that is protecting the wires.disconeted the two wires and replaced the new ignighter. put everythin back together tried it out ond guess what ??? it works .. Thank you

My mom did the repair for me. We did not have the right tools for the job which made it harder to do. First I flipped the breaker. Then we took out the oven racks. We then took the bottom metal part off the oven. This exposed the shield part and we removed it. Then she cut the wires and connected the new igniter the same way the old one was connected. It took about thirty minutes. We could do it again in about fifteen with the right tools. We went and priced new stoves the cheapest was 350.00. I'm so excited that my stove is working properly again.

Removed interior sheet metal to expose ignitor. Removed two nuts holding ignitor to braket. Cut wires. Attatched new ignitor, replaced sheet metal and baked a pizza.

Took everything apart and replaced

Removed covers, disconnected old igniter, spliced the new and replaced. The oven fired up as hoped!

Cut the wires and replace new ignitor very simple

Simply lifted out the old burner assembly (no tools needed) and drop in the new replacement.

Aging igniter glows but does not draw enough current to open the gas valve. Replaced igniter and it is working properly now.

I took the entire bottom inside of the oven apart except for the gas tube. The first time I did this it lit up, but it was so slow to heat. About 2 weeks later the oven wouldn't even light. I took the bottom out again and turned it on and held a grill lighter next to the gas tube and it was obvious no gas was coming out. I did some reading and found that if the igniter is not pulling enough amps the gas valve will not open, and that would explain why a couple weeks before it took forever to heat up. The igniter was on its last leg then died. So I ordered this part. It came in within 3 days!! Before I began the install I watched a few youtube vids on how to install the lighters and every oven they showed you just had to plug it into the safety valve. Simple enough right. HA!!! Of course I have an oven that Kenmore decided to make difficult. So..... 1) Removed the bottom cover inside the oven 1a) Turn off power to oven 2) Removed the flame spreader 3) Unbolted the old igniter 4) Remove the heating tray (not inside the oven, on the outside at the bottom, just pulled right out) 5) Find 2 wires from the old igniter 5a) My oven had only 1 wire going into the safety valve and another wire going into the power source 6) Cut the wires to the old igniter and remove old igniter 7) Bolt on new igniter and run wires down the hole 8) Cut new igniter wires to desired length (The new igniter length was too long in my opinion) 9) Splice the new igniter to the old wires still inside oven 9a) Top wire to gas valve, bottom wire to power 10) Reinstall all oven parts and hope you didn't drop too many screws :)

My husband is the repair genius. I just stand and watch but he had it fixed pretty quickly. Oven wouldn't work on Wednesday (holiday) when I had a house full of company coming. Had to use the oven in my microwave/oven/ convention/hood. Didn't think I could find a part for an oven that is over 10 years old.Could not believe that I ordered the part at 3 pm on Thursday and it arrived before noon on Friday and my husband had it fixed by 1 pm. You guys are great.

I am a 69 yr. old woman. I carefully removed old ignitor, keeping track of where everything reattached and how to reconnect. Had to strip the wires and reconnect. Very easy. From start to finish, less than 30 mins. Was so proud of myself.

I started by watching a YOUTUBE video that gave me the solution to the problem (Igniter). The instructions that came with the part were fine, but the print was so small I had to use a magnifying glass to read them (Honest). It took about an hour to complete but that included the time I took cleaning the burners and area around the bottom of the over. I turned it on, and it has be working fine. It acually heats up faster than I was used to.

Snipped the ignier wires at the igniter attached the wires with the ceramic wire nuts and replaced the igniter with two screws. Works like a champ and mama is happy.