2VED27TKFW01 Whirlpool Refrigerator - Instructions

All you need is nut driver. Top hinge has 3 screws. Once you remove the screws, lift door. It is light. I place door of my sofa. I removed screws and pried the cam insert with a spatula. You can also you flat screwdriver. I also replace the other piece located at bottom of refrigerator. Now place door back onto metal rest. May need someone near floor to guide you. Once on the rest, close door and replace top screws. Forgot to mention that I emptied door shelves before removing door.

Removed the door, removed the old lower door cam, and replaced with new cam.

Followed the Partselect instructions - removed door, removed old cam and replaced with new cam. One lesson learned. There are two cams - one that sits on hinge below door and one that is up inside bottom of door. If you are replacing one, replace them both.

I removed the door and switched out the cams on the bottom. Super easy. Door closes perfectly now.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Ordered new glass shelf installed it.

I would never attempt an appliance repair but after watching the video instructions for installing this part I decided to give it a try even though I'm dangerous with a screwdriver. After retrieving a nutdriver from my $39 handy dandy tool set, it was a piece of cake. Upper hinge cover, hinge, door removal, comes off in a matter of minutes. Only problem surfaced when I went to install my new cam in the lower hinge. It didn't fit. It was actually for the upper door hinge. I reinstalled the lower plastic piece (whatever it's called), tightened it down, put the door back on (you can do it yourself if it's the refrig. side) and popping sound was gone. I guess the bottom hinge plastic piece was probably loose but you can't tighten it unless you remove the door. I now have a upper door cam in my drawer ready when it fails and will replace it without hesitation.

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

It just slid into place, simple at that. Ordered part online, got email with day it was shipped, order details and expected date of delivery. Quick, effiecent , piece of cake.

Took the bolts at the bottom of the door off and removed the door. Pried out the old cam and put the new one in. Put the door back on and it works like it is brand new. The fridge is 13+ years old

1. Cleared all the food items off the broken shelf. 2. Removed the old shelf. 3. Removed the new shelf from the shipping box. 4. Inserted the new shelf. 5. Replaced food items.

Unscrewed the rear water valve and water line, and front water filter which allowed me to remove the old drip tray. New drip tray is smaller than the original tray, so I needed to put blocking in to keep tray under drip spout. Refastened the water filter, water valve and water line.

This is for the refrigerator, not the freezer door which is more complicated. First empty the refrigerator door of food and removed the shelves. Remove the hinge cover on the top hinge by removing one bolt. Then, holding the door, remove the top hinge by removing the three bolts in the bracket (not the bolt in the recessed hole). Lift the door off the lower hinge and lay the door on its edge on the floor. Pry the old Door Cam out of the hole in the door with a knife (my Door Cam was ground completely flat). Insert the new Door Cam. Remove the old Lower Door Cam from the lower hinge and insert the new Lower Door Cam. Pick up the door and lower the door onto the lower hinge ensuring the lower hinge pin inserts into the hole in the Door Cam on the door. Reinstall the upper hinge and insert bolts without tightening. Align door and then tighten hinge bolts. Reattach top hinge cover and tighten the single bolt. Test the door to ensure it closes and stays closed. I had to remove the door a second time to rotate the Door Cam slightly to ensure cams were better engaged (tongue in groove style) when the door was closed. Reinstall the shelves and load the door with food.

repair went good .only had problem removing tube from clip in front