2VED21ZKFN00 Whirlpool Refrigerator - Instructions

Great video on-line - remove door by unscrewing bracket (3 screws) at top of door; the door magnet will hold it to the face of the frig until you are ready to lift it off... Lift door off and position horizontally across a padded table or sawhorses. The door is actually very light in weight. The cams at the bottom were easy to put on - use care not to overtighten the retaining screw. The top thimble takes a lot of time to "dig out" of the top of the door - hard not to mar and bend the door in this area. This took almost one-half hour to get it out!! Putting in the new one, use care to not cave in the door corner, not a lot of structural strength in the area. Once all the door items are in place, put the door back in place on the frig and replace the top bracket to hold it in place; watch to line up the gap between the frig and freezer door so it hangs straight. Check the two cams at the door bottom - they won't fit perfectly when the door is in the closed position and that is OK... IMPORTANT - the door should now close, but it won't automatically shut on its own until you load the door back up with your food items. Once the items are in place on the door you will see that it now closes completely with very little to no effort... just like it should. Hope this is helpful!!!

Followed recommendations from others but went with most likely by percentage = defrost timer kit. Did not solve issue. Then went with bi-metal thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part ok. Then I saw on line that I should have listened for fan operation. I checked and found the fan motor to be defective. Replaced the motor and refrigerator worked fine. Both the motor and bi-metal thermostat were required. Should have checked fan operation first.

Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!

Openned both doors and removed lower grille. Closed doors and placed a piece of wood underneath door. The piece of wood slightly taller so that it supports and lifts the door while I worked. Working at the bottom of the door removed both upper and lower plastic cams and replaced with new ones. Be sure to tighten the single screw that holds down the plastic cam; if you leave them loose they will split/crack because they will move as you operate the door.

Easy fix. Used this a teaching opportunity for my 18 yr old son and had him do all the work. The cams have like little inclines that as the meet close the door with like a over center effect. Empty the door. Just undo the top plate 5/16 screws and lift door off. On bottom of door change the 1 piece lower door closing cam and on the bottom post plate change the door cam. add a little grease and reverse the process to install. later in life my son will know how to make this repair.....easy to do folks.

The fix was easy. I jacked up the unit and put on blocks. I used socket and ratchet removed the wheels. Reinstall new ones and let off the blocks.

I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

The instructions on line suggested I buy a lower door closing cam and a thimble top which I did. When I went to install I noticed that the door hinge with cam was also warn down. I had to again place an order and again remove the door to install. I would suggest those having this problem that they look at the hinge with cam also before ordering.

Removed the refrigerator door (after taking everything out of the shelves). Took the old Lower Door Closing Cam off (it was totally worn down), installed the new one, rehung the door. Rehanging the door took a couple of tries to get it properly aligned. Very easy fix, We thought we had to replace the refrigerator since it is 14 years old, but this fixed the problem completely!

remove contents of door-----------hardest part of chore remove top hinge cover remove three top hinge screws remove door and lay on table remove two screws holding black plastic cam piece in door, remove black plastic piece (slightly held in by some type of mastic) just pull till it comes our insert new piece, insert two screws lubricate parts mount door on hinge pin insert tip hinge pin and plate and fasten with three screws attach cover............reload refrigerator door taking opportunity to throw out old bottles and mystery jars Finis

1. Cleared all the food items off the broken shelf. 2. Removed the old shelf. 3. Removed the new shelf from the shipping box. 4. Inserted the new shelf. 5. Replaced food items.