2DLSQ7533JQ5 Whirlpool Washer - Instructions

Repair went really well thanks to the video PartSelect had posted with the drive motor coupling. It showed me how to take machine apart to replace the coupling. Loved the step-by-step instructions. Made it so easy for my son and me to do together and I am a female.

The instruction video provided is complete, accurate, and easy to understand. Follow these instructions exactly and it will be as easy as promised.

Super easy. Pulled off the top Fabric Softener Liquid Dispenser cap. Removed the seal. Loosened and removed the bolt (You'll need a socket extension for that). Removed the gear assembly workings and the top agitator. Removed the lower main agitator. Replaced with the new one and put everything back the way it came off. I must also note that I ordered the part from Part Select.com on Monday, and received it the very next day at noon.. Without using "next-day" shipping. How is that possible??? Part Select.com is the best!!!

Followed instructions on part pkg and looked at video online

Follow instructions in part repair video from part select,but put washer on back first to see if can access area without removing the whole outer cover we did not even need to do that step only took 20 minutes to replace coupling. The video was great

We watched the how to video...repair took less than 15 minutes. You can't go wrong if you just watch the easy to follow video! Washer works as good as new.

I found the impeller, in the water pump, had worn thru the front pump housing. Allowing water to leak on to floor. Replaced pump from under washer. Removed two hose's and two retaining brackets. Aligned pump and refastened hose's and retaining clamps. Works great. Thanks to Parts Select for the right part and the right price. Also Fast shipping. Dan H. Poplar Grove Il.

You have to determine if it is the COUPLING or the TRANSMISSION or the CLUTCH. I checked the coupling and that wasn't it. The machine did rotate back and forth in the wash cycle so I thought it would be either the clutch or the timer assembly. I ordered the clutch and used the video to guide me through the installation. One problem was the PUMP was stuck on the shaft so I removed the hosed and took out the rest as one unit. The clutch was full of crud and after replacing it and checking for leaks, the machine runs perfectly now! I would suggest you replace the hose washers when you reattach them to the machine as I rechecked after turning on the water and found a TINY drip that would have been a problem over time!

THe repair went well.

Friend of mine did it well

I watched a video online to see how to take it apart, what size socket wrench to use, etc. Very simple. Once I had it apart, there was a problem with the agitator itself coming apart into pieces. I realized that I was going to need the whole agitator rather than just the dog ears. So I ordered it and had it installed very quickly and easily.

don't know, I ordered the part and my husband repaired it. Did not take him long at all.

The repair was fairly simple - the hardest part was taking the shell of the washer off and putting it back on.

Tipped the washer on its side and took the pump off then the motor then the coupling.

NOTE ! When looking up part and action to take be advised there are two models of agitators. One [the first you look up ] shows you how to repair the agitator . Mine was not this style . As I watched the video mine did not come a part , and when I tried to remove top part clearly it was not the same. Further review of parts I found a complete non serviceable agitator . As I watched the video this confirmed my style of part. As for the repair, once I found out I had to order a complete unit it was simple. Remove the top cup to expose cover, then use needle nose pliers to remove the cover to gain access to the bolt . The cover has an "O" ring to seal liquid from the bolt , save and clean it up and put a little lube on it to reseal same. I can't remember the size , either a 1/2 or 9/16 socket with a 12 in. extension and ratchet will work to remove the bolt. Put a small amount of lube on the shaft , install the agitator ,secure nut , install cover and cup and you are good to go. Hope this helped out and be sure to view the the proper video.