2DLSQ7533JQ3 Whirlpool Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Agitator was banging. Top of agitator had to much play and the gear locks were worn.
Remove softener dispenser. It is hard to do, but it does pop off. Reach down inside and remove the cover. The cover has a handle. Clean the rubber gasket. The bolt holding the agitator can be removed with a socket. You will need a 12" extension. Hold one the fins on the bottom of the agitator and remove the bolt. Remove the agitator. I would recommend ordering an new rubber washer and bolt. I did not, I removed the washer from the old agitator. Install the rubber washer and place the new agitator in the washer, tighten the bolt. Use some petroleum jelly to lube the rubber washer on the cover. Install the cover. Snaps in place. Install softener dispenser. Snaps in place. Test.
Parts Used:
-
Craig from Johns Creek, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
washer not filling up
handy man did the repair and it took him about 15 -20 min when I order the part is was in the mail the next day very quick I like that susan I will use your store all the time.
Parts Used:
-
SUSAN from WOFFORD HEIGHT, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
No water coming out.
I followed the instructional video step by step with additional patience.
Parts Used:
-
HERNANE from HICKORY, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Used machine, unknown age, with zero upper agitator motion. The upper agitator could be turned easily in either direction.
Age and condition of the washer were unknown. I had no agitator grease available. I went for just the replacement of the Agitator Directional Cogs. I reviewed the video for replacing the whole kit. Removed fabric softener dispenser and the seal below. The seal needed to be cleaned. Removed the 7/16" bolt with a socket and extra long extension. Removed the agitator. Pulled off upper agitator. The part that holds the cogs is in about the center of the upper agitator. It also needed to be cleaned. One original cog was broken the other were past needing to be replaced. Replaced the cogs and the retainer. There was some effort with getting the upper agitator down far enough to re-install the bolt. That was just a slight alignment issue. The other parts were put back in place.
Parts Used:
-
Calvin from Homestead, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
leaking on tub fill
-
Timothy from Chandler, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
pumps water but will not spin
I did repair myself with your instructions. it was very easy to do for my age. 84.
Parts Used:
-
walter from grove city, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
bushing between motor and transmision broke
watched the video on line showed how to do it took about 45 min no problem
Parts Used:
-
NAN from mt carroll, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
over a few days washer would fill up with water
I googled Whirlpool washer and then water valve on my I Pad and it showed me step by step how to fix it. Thanks Partselect for the great service. Jimmy
Parts Used:
-
Jimmy from Tarboro, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
washer would not spin or agitate.
electric unplugged, removed water lines. two screws on back of control housing removed, tilted housing back, removed two clips on top of washer housing, removed body. tilted washer backward, removed brackets on water pump and electric motor, pulled motor off and removed broken parts on shaft, replaced with new parts. Lining up motor shaft to washer was a bit tricky but time and patience got it togather. replaced brackets on motor and water pump. put washer upright and put body back on the body has to be set on guides correctly or will not set right. replace clips andtilt top down and screw it. hook up water lines, and electric.
Parts Used:
-
Gerald from White Cloud, MI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!