28FN-7CXW Magic Chef - Instructions

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!

The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.

Removed the glass cover and replaced the bulb. Very simple.

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

Range is a 1967 model Maytag. First I removed drawer under oven, unplugged the range and pulled it out from the wall. Removed oven door by positioning it in the partly-open detent position, then pulled up to remove the door. Next I removed 7 screws per side panel: 3 in front and 3 in back, and one on top under cooktop, which retains the cooktop hold-down clip. With side panels removed, I noted the oven door spring position on the intact left side, then replaced the right-side spring first using the same spring adjustment positions. As I replaced the spring, I applied lithium grease to the spring hook pivot points as well as the spring coils where they rub against the interior wall. I repeated the process on the left side. I reassembled the side panels, oiled the door hinges and reinstalled the oven door. Reinstalled range and bottom drawer. The oven door operates like new, and the new springs are totally quiet — good for another 47 years!

used drill to remove old screw

I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.

Pulled the range away from the wall and took out all the screws of the back panel. I had two different screws. Removed the dial and took two screws out behind the dial. Carefully removed the wires and placed them on the new switch. Screwed switch to panel, replaced dial and put the back panel back on range. Pushed range back into place.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

I UNPLUGGED STOVE, removed panel covering the controls, removed the knob on front and the two screws there that hold the control in, inserted new control and replaced the two screws on the front that hold it onto the stove, used needle nosed pliers to unplug one connection at a time from the old control and onto the new control in the back. When I had all connections plugged onto the new control I re-installed the panel cover with a screwdriver, plugged the stove back in, and the burner is now working good as new!

New receptacle element. I am a girl and I did it.!!!!

Replaced light bulb.

1. Removed racks 2. Removed two screws holding in the bake element. 3. Gently pulled out the element exposing the two wires connected to it. 4. The two wires were held by a clip connection. 5. Removed the wire clips holding the wires. 6. Attached the clips to the new element and re-installed the element. New problem: The element did not heat up. A repairman informed me that the selector switch was damaged during the burnout- that switch was no longer manufactured and was discontinued. Whirlpool company was checked and indicated that there was a new part # 7403P023-60 but that was discontinued too. I was able to get the element working by moving the selector switch to the "Bake" position and then moving the switch about 1/4" in the clockwise direction. The element heated and the oven works at least for now as I search for a replacement part. PartSelect was an invaluable aid and helpful all along the process.