Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 253952510

253952510 Kenmore Dehumidifier - Overview

Get Parts and Repair Help for 253952510

If you know the dehumidifier repair part you need, you can browse the list of all parts on the 253952510, or you can search by name or part description. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$31.97

Float

If the bucket is full indicator on your dehumidifier is on, but the bucket is empty, or your dehumidifier is overflowing, you may have a problem with the float. This device is loca...

$25.98

Auto Shut Off Switch

The auto shut off switch is for dehumidifiers. If the water bucket is not attached properly the switch will ensure the compressor does not run. You may need to perform a continuity test on the switch to determine if the part has indeed failed since you cannot tell by looking at it. Make sure your dehumidifier is unplugged before you begin. Consider wearing gloves to protect your hands while performing this task. This is a genuine OEM part that comes straight from the manufacturer.

$6.59

SCREW

$1.08

LENS

This indicator light lens protects bulbs in ranges, ovens, stoves, and humidifiers. The lens keeps the bulb from getting cracked, scratched, and damaged. It is 1 inch long and 1 inch wide. If your lens is defective or broken, or the bulb is easily getting damaged, replacing the lens can be a solution. Refer to the installation instructions provided by the manufacturer for further accurate guidance. Remember to unplug your appliance from the power source before starting this project and wear gloves to ensure your hands are protected.

Water Container Reservoir

This container no longer includes the float. Must order float separately.

$96.49

Humidistat Control

This is a humidistat control for a dehumidifier. The humidistat on your dehumidifier responds to the humidity in the air to determine if the appliance should continue to dehumidify or shut off, based on the desired humidity level. This control needs to be replaced if the dehumidifier wont shut off when the desired humidity level is reached. This part is approximately 3.5 inches long and 1.5 inches wide. The part will be easy to replace, simply remove the front cover, remove the humidistat from the bracket, and remove the two push-on wire connectors. Reverse this process to reinstall the control. Be sure to disconnect power to the dehumidifier before completing this repair.

$6.59

SCREW

KNOB-CONTROL, (2)

MOTOR-FAN

$102.23

THERMOSTAT DEFROST

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

This dehumidifier is the best we have ever had but the water reservoir container split and the float broke off.

  • Customer: Shelah from Grove City, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 15 people found this instruction helpful
Never dreaming I could find a replacement, I went searching on the internet anyway and found the model which had been discontinued however the container and float were still available. It took two minutes to put the new float in and the reservoir container on the unit. It works great!!! read more

Unit would run continuously and not shut off

  • Customer: Jonathan from New Oxford, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Removed the front cover and then the humidistat from the bracket. Two push on wire connectors and then reversed. Very straightforward and excellent part matching. Given the prices for new dehumidifiers it was great to breathe life back into this unit which does its job well. Thanks for the easy to use web site and fast fast service! read more

We lost the water float. Needed a replacement

  • Customer: Bob from Omaha, NE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
The float has two prongs that fit two snap fasteners on the reservoir tank. I just pressed the float prongs into the snap fasterners and inserted the reservoir tank into the dehumidifier. Turned the switch and pressto! We are in business. read more