Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Blown thermal fuse for Ice Maker
After disassembling, the thermal fuse I ordered were not and exact fit, I had to cut off the ring terminals, strip the insulation back and splice it in. It works.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker would dump ice one time and then stop. Turning the ice maker off for a minute and back on would repeat the process.
I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker . To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start . FED-EX UT to MN was 13 days to deliver .
BOUGHT NEW ICEMAKER TOOK TWO SCREWS OUT, UNPLUGGED THE ELECTRICAL CONNECTION. REMOVED OLD ICEMAKER, PUT TWO SCREWS BACK INTO REFRIGERATOR(DON'T SCREW ALL THE WAY IN AS THE NEW ICE MAKER WILL FIT ON. HOOK ELECTRICAL CONNECTION AND ADAPTER (THAT COMES WITH IT). PUT THE DRAIN TUBE IN ITS SPOT, HOOK ICE MAKER ONTO THE TWO SCREWS TIGHTEN EM DOWN. I DID THIS RIGHT BEFORE I WENT TO A BIRTHDAY DINNER WITH MY HUSBAND, WAS ALREADY DRESSED AND READY TO GO AND I TOLD HIM ILL PUT IT IN SO WE CAN HAVE ICE WHEN WE RETURN. ENDED UP BEING A SURPRISE PARTY FOR ME AND WHEN WE RETURNED WE HAD ICE. IT WAS SO EASY EVEN A GIRL CAN DO IT!!
Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick
Occasionally, we'd get one batch of ice cubes and a frozen lake of water in the bottom of the ice tray.
The installation was easy and I won't bother duplicating the comments of others who have installed this part.
One word of caution: The ice maker contains a heating element on the bottom. That element is apparently live even when the ice bar is in the upper (off) position. When I unscrewed the old ice maker and went to lift it off the bolts, I severely burned my finger on the bottom of the old ice maker because apparently I started the repair in the middle of the heating cycle.
I highly recommend that you unplug the ice maker entirely before doing the replacement and gingerly ensure that the unit isn't hot before touching it. You'll save yourself a nasty burn.
watched the video (VERY helpful) and then removed the old icemaker and replaced it with the new one. Difficult only because of the small working space in the side by side freezer plus you can't see what you're doing when you tighten the screws. Working like a charm now.
Removed 2 screws that hold ice maker in place. Unplugged and took out of freezer. Used the screws I took out to put new ice maker in. Plugged in the power and in 2 days I had a full ice bin and haven't had any worries since. Should have replaced the broken one along time ago but thought that the process was harder than this. Very easy and suggest this to anyone having ice maker issues. Less than $100 and never have to buy ice for the house again.
I ept finding clumps of ice in try as though water was spilling over ice maker tray.
I loosened the 2 1/4 inch nuts with a nut driver, disconnected the wire harness, and removed the old unit. to replace, I simply connected the harness and bolted the unit back in. The job took about 10 to 15 minutes and the new unit works better than the old one ever did.
I removed the compressor start relay and replaced it with the new part. Initially it did not work. When I checked my work, I had to tighten the connector on the new part. Once I made the correction, the freezer is freezing normally again.
loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws
The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.
removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do
After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!