Models > 2537480240H > Instructions

2537480240H Kenmore Freezer - Instructions

All installation instructions for 2537480240H parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 2537480240H
31-45 of 330
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drawer rail was snapped so it would not support the drawer

  • Customer: wendy from sandown NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Took whole shelf out. Unscrewed the old rail, screwed in the new rail. Female 55yrs old. I broke it myself and fixed it myself! Very easy!!!!

Cracked drawer

  • Customer: Jaime from Harrisburg PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
I slid out the old drawer and slid in the new drawer. Easy as that! I would recommend this website to anyone.

the rail broke on the meat drawer holder

  • Customer: Geronimo from McAllen TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
I removed the shelf that hold's the rail's then one (1) screw that hold's the rail in place then I replaced the shelf. Simple & Easy!!

Fridge side warm. Freezer was ok.

  • Customer: Doug from Folsom CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
Popped off the front plastic cover on the bottom of the fridge, under the doors. Two screws held the defrost timer on under the front side of fridge (below freezer door). You can't really see the timer except for the adjustment knob that is accessible through a hole. Once the screws are removed, disconnect the wire plug and remove and replaced unit. Works fine ever since.

The retainer bar broke

  • Customer: Ann from West Valley City UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
Opened the box, took part to refridgerator and inserted retainer bar in place.

Had no freezer shelf.

  • Customer: Bettie from Toledo OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
I had to cut a little of of the ends of the shelf to make it fit. I used an angle grinder to get the job done and the shelf fits perfectly. By the way I paid for 3-5 day shipping and got it the very next day can't ask for better service than that.

Refrigerator quit running

  • Customer: Frederic from Daytona Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 10 people found this instruction helpful
I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

i smell very bad smell coming from refrigerator

  • Customer: Arsen from Glendale CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 14 people found this instruction helpful
I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.

Broken Refrigerator Door Shelf Retainer Bar

  • Customer: Ward from Stockton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
We took off the broken bar and put on the new one. It clips on. Took about 10 seconds and could have been done by a 5 year old.

Broken meat tray support rail

  • Customer: Henry from Newbury MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Pull out the shelf and remove the one screw that holds the support rail in place. Remove broken rail, slip in the new one, then replace the screw. Done!

It takes longer to remove items from shelf and clean it than it does to replace the part.

broken rack on freezer door

  • Customer: Louis from St Augustine FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
just slipped the part in place

the drawer support rail broke

  • Customer: Tara from Winsted CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
it was very simple, my husband did it. had to take the top shelf out and screw in the support rail and that was it. couldn't have been any easier. this was the easiest process from start to finish that we ever had. looked up on line, found your website, ordered the part and it arrived in a couple of days. So easy and your company was most efficient in having the part and in processing. Couldn't have been mored pleased.

rack door broke in half

  • Customer: Lisa from Milwaukee WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
Rack door slid into place easily. Repair required no tools and took maybe 20 seconds to install!
Very easy job!

rt slide for meat drawer broke

  • Customer: linda from garden city NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
easy. took glass tray that held meat draw out. unscrewed old rail screw new one in. put glass try back in frig. put meat try back in.

Refrigerator was not cooling

  • Customer: Vicki from Johnson City TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 9 people found this instruction helpful
This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!
All Instructions for the 2537480240H
31-45 of 330