25371822104 Kenmore Refrigerator - Instructions

Insert new glass into slot. Took less than 2 minutes.

Parts arrived in two 2 days, lmpressive! Snaped on the shelf bin, took longer to remove the food than to pull out the shelf, remove screw and screw in the new drawer rail. The parts had easy to follow instructions. One of the best on line experiences I've had! Thx. L.

Exactly as the video showed, except I had to take the evap coil cover off and use a hair dryer to thaw it out. It was still frosting up too much, so I ordered the thermostat as well. Both were really easy, once i saw the location of the defrost timer and the thermostat. Thanks for the great site, prices that put the big store to shame, and the good video too!

Removed shelf unscrewed screw on both supports replaced and secured.

Refrigerator and freezer was not cooling sufficiently due to an inoperative evaporator cooling fan. Replacing the mini evaporator fan was extremely easy. Here are the steps needed to replace the fan. Step 1: Unplug refrigerator/freezer main power cord from the electric wall outlet. Step 2: Remove the food rack from the freezer compartment. Step 3: Using a 1/4" nut driver, remove the (2) 1/4" screws that hold the freezer vent panel/temperature control in place. Step 4: After removing the screws, disconnect the motor's wire harness connector which is located on the top left corner behind the freezer's vent panel/temperature control. Step 5: Pull away the entire vent panel/temperature control panel and lay it flat on a table. Step 6: Remove the vent cover from the main panel by holding the left side and the right side of the vent cover and squeeze both ends at the same time. Step 7: With the motor now being visible pull the motor's fan blade straight off. Step 8: Using the 1/4" nut driver, remove the (2) screws that hold the motor bracket to the rear of the main panel. Step 9: Using the 1/4" nut driver remove the (2) screws that hold the motor to the bracket and the (1) ground wire screw. Step 10: Install new motor back onto the bracket with the original (2) screws and the (1) ground wire screw onto the same locations.Step 11: Re install the (2) screws that mount the fan bracket to the back of the main vent panel.Step 12: Push the motor's original fan blade back on the shaft until it's fully seated. Step 12: Snap back in place the small vent panel back onto the main panel. Step 13: Push in place until you hear a click, the motor's wiring harness connector back onto the top left corner of the freezer's main power wire harness connector. Step 13: Push the main vent panel until it's in place and then reinstall with the original (2) 1/4" screws. Step 14: Reinstall the freezer's food rack back in place. Step 15: Plug in the main power cord into the wall outlet. Get ready to enjoy ice cold drinking water and a super cold freezer. Pete,your weekend mechanic

I slid the old retainer bar clip piece off of the bar and slid the new one on and pulled the old crisper drawer out and put the new one in.

replaced broken shelf with new shelf

the new shelf just slide into place. It was very easy to get the part and put it in.

I ordered a new part and simply slid the drawer into place. The part fit as described and cost me less than another site selling Kenmore parts direct.

We ordered a new bracket and it was installed and in in less than 10 minutes.

I unpacked the materials and put them in place in the refrigerator. It was simple so no instructions were needed. I was very pleased with the quickness of delivery.

it was easy my wife did it wen i went to the fridge it was already installed. thank you!!!!

took the shelf out of box. Opened the of refrigerator door placed shelf on door pieces that held it. pushed down on it, shelf locked it in 2 minutes

Installed Metal hinge(old hinge was plastic) to take out sag of door.(painted the hinge color of refrigerator as hinge doesn't have plastic appearance cover )

moved freezer items to right of icemaker,loosen two nuts lifted icemaker over nuts,squeezed and pulled cable out turned over marked L bracket screw with marker for location plugged cable in tighten screws,made ice in 2 1/2 hours john