All Installation Instructions for Kenmore Refrigerator 25365812508

Defrost timer was not working

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

Parts Used:

Defrost Timer - 60Hz 120V

Harold from Grants, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Dairy door was cracked by an item in the refrigerator and broke into two pieces

This was not technical at all. The old door fell out and the replacement door snapped right into position. It was simple.

Parts Used:

Dairy Door - Clear

George from Pottsville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

torn and cracked gasket

Took off the old one, replace the new one in less than 5 minutes

Parts Used:

Refrigerator Door Gasket

janet from Parryville, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old door seal was cracked and didn't seal tight.

Pulled off the old seal and put the new one on. No tools needed. It fit where it was supposed to and seals the door like new now! Thank you!

Parts Used:

Refrigerator Door Gasket

Rosemary from FRUITPORT, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old gasket was cracked, dirty, and causing the refrigerator to run overtime.

Easy to peel out old gasket, and new one tucked right in. I was embarrassed that it was so easy and I waited so long. Has made a big difference in how the frig looks and also operates.

Putting the shelf in was a no-brainer. It comes with matching slots and you can't put it in upside down or backwards. Only the right way!

Parts Used:

Refrigerator Door Gasket

Door Shelf Retainer Bar

Bonnie from ARCATA, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old gasket was torn and falling out

I removed the old gasket and cleaned the area. Then I started at the bottom and pressed the new gasket into the door. You must use firm pressure and go all around. It does get tricky hear the end as it seems like there is excess, but it will fit. Just keep using firm pressure.

Parts Used:

Refrigerator Door Gasket

Cristina from MARLBOROUGH, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Intermittent loud noise coming from fan motor located in freezer compartment

Ordered a new evaporator fan motor and watched the repair video supplied by part select on their web site.It was spot on step by step instructions

Parts Used:

Evaporator Fan Motor Kit - 120V 60Hz

Donald from Okeechobee, FL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

crack

pull off the old gasket and push on the new one into the channel...

Parts Used:

Refrigerator Door Gasket

w l from PIKESVILLE, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

bought brand new and kick plate was missing

just snap it on

Parts Used:

Kickplate Grille

Lloyd from HASKELL, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Freezer froze up/ Fridge ran warm

Thawed out freezer, I recommend laying a couple old towels in freezer to soak up melted ice. Replaced old thermostat with new part. Removed 2 screws, removed back plate, unplugged 2 connectors and cut 2 wires. Crimped in new thermostat and repositioned to original part location. Reconnected plugs as I reinstalled back plate. Installed 2 screws and connected power. Works like new! Trouble shooting and part installation video is very helpful, great site!

Parts Used:

Defrost Thermostat

will from bushnell, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bar had broken

Simply replaced by hand. No tools necessary

Parts Used:

Door Shelf Retainer Bar

John from BRONX, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Freezer worked, no fridge

Removed panel over the motor in the freezer department. Removed screws holding the motor in, unplug wires. Reversed process to install motor.

Parts Used:

Evaporator Fan Motor Kit - 120V 60Hz

Adam from BERKSHIRE, NY
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Freezer worked, refrigerator didn't. Ice build up on coils.

Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.

Parts Used:

Defrost Thermostat