22JK-7KLXV8 Magic Chef Microwave Oven Combo - Instructions

Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together

part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.

Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.

Simply pull off the old knob from the stem, then push the new knob onto the stem. NOTE: This part works for the POWER BURNERS on the Maytag MGR4450ADH - the stems and knobs of the regular burners are different.

Overall, it was painless and easy with zero problems

Unplug appliance. Remove total of 7 phillips screws from sides and front of bottom panel . Panel front drops down, remove one socket screw and socket. Now have access for lineman' s pliers to unscrew bulb base. Reinstall socket, replace bulb and 7 panel screws. Restore power.

Removed one screw lowered glass cover removed burned out bulb replaced with new one put glass back reinstalled screw. Dune 5 minutes back in business

1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS

Accessed igniter removed 2screws holding it.unpluged igniter installed new one.

Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.

removed oven floor, removed two screws in element . pulled out element wires, secured them so they would not fall back into slot, snaped in new element . scewed it in place , replaced floor . thanks partselect.com

If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.

I read all the reports on your site pertaining to oven igniters and decided to order one. I was amazed when it arrived the next day. I got a lot of tips reading others replys so I lifted off the oven door, took out the racks, removed the 2 screws holding the old igniter and tried to pull it out. There was hardly any slack in the wires, so I pulled the stove away from the wall, took off a breadpan size cover in back and found the wires were zip tied to a tube. I cut the tie and unplugged the wires, but the new plug didn't match so I cut the new plug off and rejoined the wires with butt to butt crimp connecters, which I prefer to wire nuts. I used the insulation and new cover from your kit as my old part had the long ceramic insulator and put it all back together. It works like new again and saved me a lot of money. I am very pleased with your product and service, thanks.

First I removed the two screws that held the old element in place. I then pulled the element out about 3 inches and disconnected the two wires.
I replaced the element with the new one and tucked the connector in the insulation. Additional insulation came with the kit. I replaced the two screws that held the element in placed. Oven worked perfectly

1st unplug stove opened cover to wireing box with a phillips driver removed old part transfered wires one by one installed new part installed cover & pluged in stove & worked line new.