1LE5700XKW0 Whirlpool Dryer - Instructions

1. Opened the top. (UN-plugged it first) by prying between top and front of machine.
2. Disconnected the door switch
3. Removed two screws one each on top corners of front
4. Pulled top of front cover forward and lifted up to remove.
5. The drum will fallout if not careful, good time to remove drum to clean dust from inside machine.
6. With drum in place slide new belt, skinny side down around drum, to about halve way back.
7. While supporting drum reach back to the motor area, should be on right side facing front of machine. There you will find the belt idler/tension assembly.
8. Thread the belt through the assembly and around the motor drive pulley.
9. Ensure the tensioning assembly is firmly in the slots on floor of machine.
10. Reassemble housing in reverse order. took about 45 minutes

Removed back cover of entire dryer.The thermostat was accessible from that point(Just as diagram showed), removed two wires from thermostat, removed thermostat & replaced with new thermostat & plugged 2 wires back in just as instructions indicated. Very simple,15 minute job. I will certainly use again for any appliance repairs.

I watched the video to know how to change the belt. I removed the front panel and slid the belt over the tub (you will have to pick the tub up a little). Then I reached around with one hand and slid the belt over the pulley. Then I used the same one hand to push the tensioner back and slip the belt behind it. You will be doing most of the work by feeling not by vision but that's where their video is helpful. I paused the screen on my laptop where it shows how the tensioner goes around the belt. Also when you slide the belt over the tub look for the grove the previous belt left for alignment. It took me 10 minutes.

Six(6) screws were removed to separate the front and rear sections of the dryer door to get access to the rear of the catch.Pliers were used to maneuver the catch through the opening in the cabinet from the rear. The new catch was easily snapped into the catch opening from the front of the door.

I followed the video provided by PartSelect. It pretty much went exactly like the video said it would. I was pretty sure the belt or idler pully must be the culprit, but I didn't even know how to open the thing up until I saw your video. I would likely still be putting up with the squealing without that video. Now the dryer is nice and quiet. -Mike

I followed the excellent video instructions for dryer drive belt replacement. The tensioner proved to be a little tricky. I also had to fiddle the drum back into position. Now that I've actually done the repair, it would take half as long if doing it over.

Replaced the heating element. Everything copacetic.

actually your site was very helpful in describing each part that i chose to replace. one helpful hint to someone when installing the dryer pulley is to use the parts box to hold up the drum when installing.it seemed to be the perfect size. great site!

simple replacement

Exactlyt how your video showed me. I was a bit skeptical, but it was the easiest repair ever.Thank you

The dryer would make a loud humming noise and the seize up. I would reset the breaker and the dryer would run briefly and then seize up. I opened the dryer and cleaned out all the lint on the motor but it did not help. I spun the motor shaft and felt like a bearing inside had failed. I watched Steve in the video-he was awesome and made it all simple- and ordered the correct parts. I decided to replace the rollers, belt, and pulley as well as the motor. The repair is very easy-and worth it- EXCEPT one piece of advice. BUY the blower fan that attaches to the motor. Mine did not come off easily like in the video. The plastic shaft deteriorated under pressure from the wrench. I was forced to use a heat gun to melt/then cut the blower fan from the motor. It was not easy but don't let it deter you from the repair. I used a table vice but never could remove the remanents of the blower fan shaft from the motor. The repair was a snap after that. Great site for parts and help.

Took off the back panel of the dryer. Removed the screw holding the drying element in only to discover it would not fit out the bottom of the case holding it because it was too close to the bottom of the dryer. Had to take off the top of the dryer and remove the casing, remove the element, replace it and put the casing back. Not too difficult, only two wires and one screw. Did make a couple of rookie mistakes making me backtrack and redo a few things but nothing major.

Removed top, removed front, laid dryer on back to keep drum in place and replaced belt. Used masking to hold new belt in place while installing. Easy job. Belt was delivered in 2 days. Thanks

We followed instructions in videos from this site and youtube. The repair went smoothly and dryer works great now.