1CWED5100VQ0 Whirlpool Dryer - Instructions

replaced stock belt tensioner with one with pulley. i hope that solves my problem. just want to add that you guys saved me a ton of money ! thanks and God Bless

just looked up my make and model on parts.select. looked at other peoples problems and went thru the parts list and ordered. videos on installation are helpful.

easy to simple and hope it continues to work.

We started with replacing a thermal fuse, went onto heating element & then to replacing the high limit thermostat. The replacements went very easily with your videos, but unfortunately it did not do the job & there is still no heat.

I'm a 68 year old single lady who watched the video and just followed the instructions. Took the back off, tested all the parts involved with heating and the only part that didn't have any continuity was the top part of the thermal cutoff fuse. After receiving the part I removed the old one, put the new one in, put the back on and turned the dryer on. It heated right up. I also had a part that I didn't need and your return dept. made it very easy to return. I love this site. Save me a ton of money.

Purchased a new lint filter. Delivery and installation were no problems. The easiest repair that I've ever done.

I needed to replace our drum support rollers - one was completely worn out and wobbling (the buffalo herd noise) the other wasn't too bad, but for an older dryer(15+ years) I figured it was time to replace both wheels. I ordered the maintenance kit that also included the Idler Pulley and drum belt. I spent most of my time with the vacuum since there was a lot of dust accumulated inside the dryer. (I recoverd $1.83 in coins!) The instructions that came with the kit were very helpful for this repair. Plus, there were some online videos that heled as well. Once I had everything apart I noticed the plastic bearing ring on the drum's front was nearly worn out so I quickly ordered this from PartSelect and it arrived quicly in two days - this took only 10 minutes to replace.

I watched a video on youtube about how to install a dryer heaing element, took pictures of the wires on my cell phone, then just installed the new part. Plugged it back in and works like a charm!

Very easy to repair the heating element. I took the back off and half of it was burnt out (twice as long to dry). Replaced it and works like new. The instructional videos are great. I've replaced my water pump on my dishwasher also. Once again, instructional videos are great. I put trust in this website and their parts. I wouldn't have any worries about this site. Overall satisfaction A+.

We usedthe instructions that PartsSelect offered. Unscrewed the top in the back of the dryer lifted it up and replaced the part. A Lot cheaper than calling a repairman...

watched the video. Removed old part, installed new one - as per video.pluged it back in and started drying clothes again!

Ordered a thermal fuse . Very fast service (24 hrs)put the fuse in and is now working again

These parts didn't fix the problem. Went to you-tube watch a video on how to repair a gas dryer step by step and which parts to replace. Found out we had replace the wrong parts and ordered the coils and now it works!!! Next time I will watch a video, first then order, this will save us time and money!

Using a stiff putty knife I depressed the clips that hold the top down. I loosened the screws at the lower edge of the front panel and removed the two 5/16 head screws that hold the front on. I unplugged the door switch and lifted the front off the lower screws. I removed the drum and the broken belt. I replaced the rear rollers after applying some dry lube to the shafts and replaced the tension spring and rolled. I replaced the drum and belt and attached the belt to the small pulley on the motor. Then checked the rear gasket felt and reinstalled the front cover and the top.

You guess that it is the heating element. They are like a light bulb, they do fail. I took the back off the dryer and removed the heater element. There is a temperature switch that needs to be removed. Examining the element, you could see a break in the element wire. That part was broken. The repair went smooth and the replacement heater assembly looked the same as the old one in design. I had to reset the dryer control and the dryer is good again.