Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Handle broke
Took off the inside ( this allowed me to clean the glass) panel. Removed the two end parts with a screw driver. Replace the parts and we were good to go.
Repair went a lot faster and easier than I anticipated. Instructions are similar to those posted by others. 1. Verify that new gasket looks mostly like old gasket as best you can since not all of old gasket is visible. 2. Shut off circuit to oven (optional, but good practice) 3. Remove racks, trays, etc from oven to reduce weight at Step 7 4. Remove oven door by partially opening door to broiler position (about 20 degrees). Door should catch and stay open on its own. Slide up and lift off door. The “hinges” are spring loaded so carefully return them to closed position so they won’t snap shut on fingers. 5. Remove Phillips screws, one on each side wall of oven liner. 6. Remove two hex screws and metal gasket-holder on top center of oven liner. 7. Pull and slide oven liner out of oven mainframe about 1/4 “ to 3/8”. This may be the most difficult part of the job. 8. If possible to remove just a couple of inches of one bottom of old gasket (right side is easiest), verify that the cross-section profile of both old and new gaskets are essentially the same. If not, you have the wrong gasket. 9. Pull and remove old gasket. If gasket is dry and cracking, it may be necessary to scrape it out with putty knife, flat-blade screwdriver, etc. if it has fused to metal over the years. Note how it was installed on the metal edge of the oven liner. 10. Locate the mid-point on the new gasket length and begin inserting it at the top-center of the oven liner where you removed the two hex screws. Continue installing along both left and right sides of the liner. Each end of the gasket should extend to just above the respective hinge. No trimming should be necessary. Ensure a snug fit all along each side and top. 11. Push liner back into oven mainframe. Replace Phillips screws, gasket-holder, and hex screws. 11. Pull out each hinge to broiler position. 12. Replace door by sliding down onto hinges. Close door and check for tight fit against gaskets. Gaskets will flatten somewhat over time 13. Restore power, racks, trays, etc.
Took door off of hinge Removed 6 screws from bottom of door Removed glass Removed screws from side of door Removed door from frame Replaced the end caps using exisiting screws Put door back together in reverse order Pretty easy but simple instructions would have made it a 15 minute job instead of 30
Open door lift door off hinges lay door face down on flat surface remove 6 phillip head screws 3 on each side lift housing out of door case remove end knob phillip head screws installed one knob insert bar attch second knob and tighten screws lay housing back into casing attach screws doing one at a time on each side slide door back on to hinges and test operate, you are done!
Step #1: Remove 2 screws at the inside top of the oven door that holds the inner/outer oven door together. Step #2: Remove the screws from the inner door that hold the plastic handle end caps to the door. Tip: Use a file to dress up the tips of the metal handle bar so that it fits easily into the new plastic handle end caps. Step #3: Install the first new plastic handle end cap. Step #4: Slide the metal handle bar into the plastic handle end cap that was just installed on the outer oven door. Step #5: Place the other plastic handle end cap on the metal handle bar. Step #6: Install the second plastic handle end cap on the outer oven door. Step #7: Reassemble the oven door by installing the screws that were removed in step #1.
This the second time in three years the end caps broke. The first time the replacement end caps slid right on but, this time it was an extreemly tight fit. I had to sprsy white greese on the handle bar and inside the end cap and, even then I thought the end caps would break it was so hard to get on.
Removed door from unit, removed two screws on the insideof the door and open door in two, (inside and outside), removed two screws from each door handle end, replaced with new ones and Bingo !!!
I took the old cap off, and replaced it with the new one. I am glad I had the sense to buy this online, If I had gotten a repairman to fix this, it probably would have costs $100.00 instead of the $17.00 it cost me to fix it myself. Thanks.
Dislodged screws to oven door to get to handle assembly. Fairly easy, however, new door handle end caps do not come with screws and the old screws were not a good fit. Almost stripped the old screw trying to get it in place. Strongly suggest that Part Select send replacement screws with handle to facilitate repair. Door handle is back up but is now loose until I can find/secure appropriate replacement screws and repeat the process all over again.
My son took care of removing the broken parts, opening the door and replacing the new handle ends and then finished! It was easy watching him do the work!!!
Very easy fix. After removing the six screws that held the door together, it was a cinch to replace the end caps and put the door back together. Works just like new!!
Repair was basically simple. Remove 6 screws holding door facing on door, remove one screw holding handle end caps in place. Then reverse the operation installing handle end caps. The problem I had was that the new a end caps had different dimensions than the old ones and the handle wouldn't slip into them. Had to carve away material inside the new caps with an exacto knife in order to fit the handle. The result was a 15 minute job took well over an hour
Unscrewed the broken door handle from the range with torqx bit, and replaced, hardest part was getting the plastic handle on the black pull bar. you may want to use a mallet.
