Models > 11084832201 > Instructions

11084832201 Kenmore Dryer - Instructions

All installation instructions for 11084832201 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11084832201
406-420 of 601
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Felt on lint filter came off.

  • Customer: Mike from Rocky River OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just put the new lint filter in.

Dryer stopped heating

  • Customer: Joseph from Austin TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

Old filter screen was torn at edge of plastic rim

  • Customer: Dan from Bluffdale UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced with new one which had been improved upon by a brace down the middle of the screen.

My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.

  • Customer: Joe from St. Louis MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Loud squealing from newer Whirlpool Front Loading Dryer

  • Customer: Scott from Bloomington IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Dryer was making intermittent squealing noises sometimes it was amazingly loud, sometimes not so bad. Still, I figured this couldn't be good so I wanted to find a fix. Read the stories here and everything pointed to the 'idler pulley', so I figured I'd give it a try. For me, access was the hardest part -- my laundry room is small and I can't easily get the dryer out or move it around. Not a problem with the part, just my own setup. Important to note that this repair is best done through the BACK of the unit, not the front. Once I got access to the back (removing AC and Water used for the 'steam dry feature') I also had to disconnect several of the electrical connectors to get the unit fully apart. Good news -- the actual replacement of the pulley took about 1 minute! It was just all of the moving and disassembly that took so long. The original idler pulley had worked its way off of the shaft and was out of place and causing the squealing. All is well now, and I saved a bunch by doing it myself. No more squealing!

Rollers squeaking on dryer

  • Customer: Dustin from Martinsville IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched a brief video on YouTube and followed step by step. Real easy.

No heat but dryer drum was spinning

  • Customer: Kelli from Plymouth MA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered the fuse first hoping it was just that simple, watched the video for how to replace, first step was to take the back of the dryer off, well I order to take the back off I had to take off the Electrical Cord, as well as he top of the dryer. Only to find out he part I was replacing was not back there. Found the tech sheet attached within he dryer though, and as it turns out only needed to take he front bottom panel off. Without testing he continuity I was just giving this a shot, the Thermal fuse did no fix it, so I tried the high Limit Thermostat and Fuse kit still no luck. Took out the Element to find I was physically cracked in 2 pieces, replaced that and I was back up and running. And all parts were found in the bottom front panel of the dryer, so beware before you watch the video and take our whole dryer apart like I did.

Horrible squealing sound - nails on a chalkboard!

  • Customer: Greg from Chagrin Falls OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First tried repairing the old idler by cleaning and lubricating the shaft. That lasted for about a week but the squealing returned. Ordered the part and had it in a few days. Replaced the idler wheel and it's been quietly running like new for several weeks now. Now wife thinks I'm Superman.

No heat

  • Customer: Beth from Jonesborough TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I purchased the heating element, still no heat. Then I purchased the thermal fuse,still no heat. I have been pleased with the prompt shipment of the parts and the parts arrived safe. Thank you for service and time, not sure what to do now.I will recommend PartSelect to friends.

broken door handle

  • Customer: Robert from Troup TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took door apart unscrewed handle and put new one

fuse went bad

  • Customer: Charles from WAYNESBURG PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you

Dryer stopped heating

  • Customer: Dorothy from Salisbury MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I needed a schematic to know exactly where the heating element was located and to be sure of what the part looked like. I found the part and after watching the video on removing and installing the heating element decided to replace the High Limit Thermostat and fuse as well. I also read some of the other reviews. The part arrived in 2 days and I did have a little help removing the old one before the parts arrived. Since the dryer was ready for the new parts when they arrived, the install was easier. I had a little trouble balancing the flashlight to see well enough and realized it was easier to put the element in then reinstall the unit, it was a little tricky getting the element sleeve back into the slot, THEN screw the thermostat and Thermal fuse onto the element housing. Since everything was open, I vacuumed all the lint out that I could, hooked up the vent hose, plugged the unit in and pressed the button. I then basked in the glow of a working heating element and I was back in business!. Thanks for the video and help. I LOVE PartSelect.

Quit running after one to five minutes - consistently

  • Customer: Walton from Leesburg VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the repair tests followed in repairman's sheet found taped behind front lower panel. When into diagnostic mode (found on paper) and tested the top front control panel buttons. All checked out fine except when I opened the door it beeped and showed a 4E code. So per the paper Tested the Moisture sensors (two metal strips inside of dryer where lint screen is) test passed, only three things left for this issue per the manual. Wire harness from two metal strips, longer wires going up from that harness to electronic control board , and the ECB itself(found under top lid of dryer). Since did not have a meter, Replaced the lower wire harness first - no improvement. replaced ECB - works perfectly now. Saved $$$ vs a new dryer.

Lint Screen Deteriorated

  • Customer: Robert from Ingram TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced Lint Screen

Dryer would not start

  • Customer: steve from hot springs SD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced Thermal Fuse
All Instructions for the 11084832201
406-420 of 601