Models > 11082832100 > Instructions

11082832100 Kenmore Dryer - Instructions

All installation instructions for 11082832100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11082832100
91-105 of 341
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door latch broke

  • Customer: Debra from Oakland NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Pop out the old latch and replaced with a new one

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 6 of 16 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

belt was cracking and dryer was somewhat noisy

  • Customer: Melody from Silverton CO
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

Dryer door would not stay closed

  • Customer: Gregg from St. Augustine FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.

Dryer door wouldn't shut

  • Customer: Amy from Cumberland RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
The door catch kit is soo easy. They give you instructions on which one to use depending on your dryer and it fit perfectly into the door. This was great especially since it was so inexpensive! My husband thought we would have to replace the door.

The male part of the door catch was broken

  • Customer: David from Chhicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Simply installed the piece and I was done. Took 10 seconds.

Dryer door kept opening

  • Customer: Jennifer from Big Timber MT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Popped out the old door catch kit and replaced it with the new one! Easy!!

No heat in any drying mode

  • Customer: Linda from Indianapolis IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed front panel located hearter elemement houseing
removed screw securing houseing to dryer chasis, disconected wireing harness- be carefull here there are three lines two for the thermostat and one for the element- you only need to disconect the one nearest the front of the unit, reove the screw holding the element to the houseing it sits in and pull out. instalation is reverse the directions to remove

Dryer door wouldn't shut

  • Customer: Megan from Kettering OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
My husband is the one who fixed the door. He said he just popped it into place and was done in just a couple of seconds! The best part though was the quick service we received...I ordered the part around 10:30 in the morning, and it was at my front door by 5pm the next day!!! What great service!!!! We will definitely do business again with PartSelect.com if we ever need more parts.

Door wouldn't fasten shut

  • Customer: Susan from Laingsburg MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Popped the latch out and popped a new one in.

The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your service. You made my life easier.

Dryer didn't have heat.

  • Customer: Stacy from New Windsor NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 1 of 2 people found this instruction helpful
I actually had a friend's husband do the repair, who is an electrician by trade. He removed the front of the dryer, removed the box that held the element, removed the element, marked the wiring, and then when the part came, he put it back in, and reassembled the dryer.

no heat to dry clothes

  • Customer: Eugene from Bradenton FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
unplugged the dryer and removed collapsable vent then we laid it on its back. took off the lower front face with a screwdriver ( just inserted in upper margin and it popped off) then removed a couple of screws and put the new element in replaced the screws and we cleaned all the old dust and lint from in the cabinet and replaced the front face. no problems.

Door handle broke

  • Customer: Rebecca from Reinbeck IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
We removed the 6 screws - two were below the clear opening and we did not find them right away. We pulled off the black cover, removed the old handle, put the new handle in place, put the black cover back on and then re-screwed it in place. Very Easy. The part fit exactly as the original.

The dryer door catch wouldn't hold the door closed

  • Customer: Gerald from Thompsonville MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I ordered the door catch kit on a Wednesday at it arrived Saturday AM. It took less than 1 minute to pry out the old catch with a flat screwdriver and pop in the new one!

Plastic handle broke completely off.

  • Customer: Arthur from Antioch CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed the screws, pulled off the front cover, removed the screws that held the old handle and screwed the new handle into place, replaced the screws that held the outer cover and that was it.

Done Job!!! : )
All Instructions for the 11082832100
91-105 of 341