Models > 11082832100 > Instructions

11082832100 Kenmore Dishwasher - Instructions

All installation instructions for 11082832100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11082832100
31-45 of 322
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Felt piece coming out of filter

  • Customer: Sara from Solon IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
Removed old filter and put in new one.

seal for lint filter came off

  • Customer: John from Midland TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 12 people found this instruction helpful
Pulled out the old and slid in the new filter

The felt strip on the filter had come undone.

  • Customer: Rebecca from Laredo TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 16 people found this instruction helpful
Took the old filter out and inserted the new one- works great!!

Door latch (female part) was broken.

  • Customer: JEANMARIE from BELLEROSE NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.

Dryer tumbled but would not heat

  • Customer: LARRY from NEWNAN GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 7 of 7 people found this instruction helpful
Used socket set to remove the two hex-head screws from the bottom flange of the toe panel. Manually pulled the panel out at the bottom, pulled down, and removed the panel. Looked to right and found heater shield. Removed heather shield using socket set. Removed the two wires from the terminal block (had to use a little WD40 to loosen connection and wiped up afterwards). Removed the holding screw holding the heating element using the socket set. Pulled HARD on old heating element using pliers and a rag (protection from accidental cut-sharp edges). Once out, the new element slid in relatively easy. Screwed the new element back into place and re-connected the element wires, then put the heater shield back into place. Put the toe panel back into place. Tested and worked great! The only thing that made this "easy" but not "really easy" is that I had to really pull HARD on the old element to get it out...with the sharp edges and tight fit in play, you'll need to pay attention to safety when removing the old element.

Dryer door catch broke

  • Customer: Bill from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.

dryer wouldnt heat

  • Customer: JEFF from LEBANON TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 10 of 18 people found this instruction helpful
First i tested each part for continuity and found out that the thermal fuse was bad. So ordered the part and went ahead and got thermostat and element to ensure no problems in the future since I already was in there.

Replace broken handle

  • Customer: Nancy from Anchorage AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
Only need to remove 6 small phillips head screws. 4 around top half (inside on door) plus 2 under door window (you have to bend down to see. Pull outer plastic ring off, remove 2 screws holding handle on, replace handle and reverse process.

Dryer would not turn on

  • Customer: Pam from Chandler AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 7 of 9 people found this instruction helpful
We took the screws off of the back, took out the thermal fuse and replaced it with the new one.
We watched a video of how to do it which made it so easy.
Works great!

Door catch on dryer door broke

  • Customer: Lynne from Jamestown CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might contact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.

broken handle

  • Customer: Karen from Charlotte NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Take out 8-10 screws on the inside of the door. Make sure you note which screws go back in the correct spots. The screws are more than one size. Plastic casing pops off then you remove 2 screws for the handle. Put handle on. Put plastic casing back on and screw back the 8-10 screws. Very easy.

Dryer not spinning

  • Customer: john from goldsboro NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 11 of 22 people found this instruction helpful
I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)

Dryer turns off after 1-2 minutes

  • Customer: Dixon from Santa Fe NM
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 6 of 7 people found this instruction helpful
I tried to follow directions followed by others on this site after diagnosing the problem via suggestions provided by users. I have a Whirlpool Duet dryer from 2002. We've had problems since moving about 3 years ago. I removed the front panel (lower) by unscrewing the two bottom screws (1/4" sheet metal screws). Then I took out the lint screen and the metal tube/contraption immediately beneath to get access to the area where thermistor is located. See the drawing/chart to help you locate this. It's really easier than it seems. Make sure you have the chart/drawing for your model - it makes difference! The thermistor came out pretty easily with a nutdriver that has a swivel offset shaft. Ask your hardware store tool dept. about that one. Put everything back in reverse order of course and test either with/without the front panel re-attached. In my case it fixed at least part of the problem. I was able to get clothes almost dry with most settings but I have yet to install the moisture sensor to see if that helps in addition to the internal-bias thermistor. I am the kind of person that does one thing at a time so at least I now know the thermistor was bad. Good luck and hang in there with your own repair. It's a lot cheaper even if it takes you longer to do than a pro.

The plastic handle on the door broke off

  • Customer: Bernadine from Anchorage AK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
I removed all of the screws on the inside of the door. Unfortunately, I found out that I only needed to remove four of the screws after the glass fell out of the door. After re-installing the glass and removing the correct four screrws, I figured out that I had to pry off the plastic face plate to get to the two screws that held on the handle. After removing these screws, I was able to get the broken handle out and the new handle in. I then reinstalled the plastic face plate and replaced the four screws that held it in place.

doo handle broken

  • Customer: Keith from Anthem AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
I followed the directions of a previous customer, using a Phillips screwdriver to remove only the Phillips screws on the inside of the door. Removed the outer plastic ring around the door. Replaced the handle (attached by two screws) and put the plastic ring with a new handle back on the outside of the door.
All Instructions for the 11082832100
31-45 of 322