11076902691 Kenmore Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old lint filter had holes in it.
-
John from Massanutten, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
no heat, no timer advancement
Disconnected electrical output, closed gas valve and line. Removed back of dryer and removed wires to thermostat and replaced with new thermostat. Did not solve problems.
Parts Used:
-
Lesley from Yucaipa, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
No heat
-
Randal from Fowlerville, MI
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
dryer wasn't heating
Followed the parts select You tube video. Was helpful. Note the Ignitor kit is very sensitive. We didn't need an ignitor right now but purchased one in case the other 2 parts didn't help the problem. We took the ignitor ( wrapped in a bag) out of the packaging and it snapped in half without even touching the sensitive end. Note handle with extreme care.
Parts Used:
-
ERIN from RED WING, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Door latch was broken
This dryer refuses to die and I am happy to keep it that way. Door latch was replaced in less than a minute using this kit. Easiest repair ever.
Parts Used:
-
William from Champaign, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
door would not close
Slipped screwdriver on top and bottom of catch and pullef out. Pressed new catch in plact. Job finished.
Parts Used:
-
Daniel from Stratford, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Felt wears on the dryer lint screen
No repair. Just replaced the screens in the dryer and they slide in and out to clean. The felt gets worn fast.
Parts Used:
-
Judy from Cloverdale, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Washer quit running when lid was closed
This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.
Parts Used:
-
Colleen from Indianapolis, IN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Long Time Drying
Un plug dryer . Take off dryer door . Remove front panel by pulling out. Remove 2 screws holding coil bracket . Remove electrical connectors ,remove 2 coils . Install 2 new coils same as old ones connect elect. Wires replace coil holding bkt. Unplug flame sensor . Remove 1 screw . Replace old flame sensor with new plugin elect. Connector replace in reverse wala ,,,alldone button up dryer plug in dryer . . Good to go.
Parts Used:
-
ALEXANDER from HUNTLEY, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
lint filter coming apart
-
Alan from Oklahoma City, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!