Models > 11072514102 > Instructions

11072514102 Kenmore Dryer - Instructions

All Instructions for the 11072514102
1321 - 1335 of 1547
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
no heat
unplug take off vent hose and back panel unscrew one bolt holding the fuse disconnect 2 wires. Connect the 2 wires to the new fuse hold in place with the bolt put back on the back panel and vent hose plug in and your done
Parts Used:
Dryer Thermal Fuse
  • Juanita from Plano, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
not heating up
pull out lint screen, removed 2 screws. lifted top up. removed 2 screws from the front,disconnected wiring harness. removed the drum and belt. located and removed the igniter, sensor, and coil valves. replaced all with new parts. reassembled. now it heats up. i believe that i only needed the coil valves. coil valves not shown on parts list, i purchased later. everything was very accessible with the drum removed.
Parts Used:
Dryer Radiant Flame Sensor Igniter Kit
  • Keith from Baltimore, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken belt
Used PartSelect instructions for routing belt & a customer's valuable guidance.
Parts Used:
Multi Rib Belt - 92-1/4"
  • Christopher from Skillman, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer would not start
Your website described the probability of the problem as being one or both of the replacement parts I bought. You were right. I replaced the two parts and the dryer started and has been operating flawlessly ever since. I would also like to commend you on your very rapid shipping of the parts. I recieved them in less than 24 hours, via Fed-Ex Ground.
Parts Used:
Push-To-Start Switch Dryer Thermal Fuse
  • Kevin from Fly Creek, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No heat in my dryer
I changed the thermal fuse following instructions from the video on the site . Very easy repair, anyone can do it.
Parts Used:
Dryer Thermal Fuse
  • Michele from Woodland Hills, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Drive belt very warn, not broken
I removed screws for the lint screen - TOP. Pry up top with screw driver. Disconnected inside top front 2 screws, removed door control wires, white and blue. Lift off front of dryer. Tip dryer back about 40 degrees against wall. Remove warn belt (not broken). Relocate idler bracket on the cabinet base, follow diagram which comes with the belt package. Be very careful that the belt is NOT on the side of the idler roller. I had to do this install a second time, because I had it wrong the first time. Even though I've done this repair 5 or 6 times, there's always a first time GOOF. Not really a hard job.
Parts Used:
Multi Rib Belt - 92-1/4"
  • Philip from Cambridge, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken dryer belt and idler pulley
Threw away the printed instructions and followed the Part Select video ,featuring Steve...
Parts Used:
Multi Rib Belt - 92-1/4"
  • Anita from Keokuk, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no heat
remove dryer door....remove two other screws on front panel [left side].tilt panel forward and lift out of brackets.thermostat is visible .remove two scews that secure thermostat. disconnect wires from thermostat and reattach to new one. secure new thermostat reinstall door and front panel.
Parts Used:
Dryer Cycling Thermostat
  • Kim from Ashley, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer wasn't turning.
Well my husband did the install and he said it was very easy??
Parts Used:
Multi Rib Belt - 92-1/4"
  • Annemarie from High Ridge, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer not staying hot
Ordered thermal fuse and cycling thermostat
Parts Used:
Dryer Radiant Flame Sensor
  • Lee from St. Louis, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The dryer was not staying hot through the entire drying cycle.
Opened the top, removed the front panel. Supported the drum with my foot while I replaced the coils. I used a very short screwdriver so I would not have to remove the drum.
Parts Used:
M Series New Style Coil Kit
  • Steven from Mantua, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drive motor burnt up
Instructions are available from other web sites. A few tips from me. Tape the dryer doors shut. When you remove the springs it falls open. Remember to just loosen the hex screws at the bottom of the front panel, it has slots and just lifts off of them. To easily remove the clips holding the motor bearings use a dull chisel or small pry bar on the outside half loop and tap the end with a hammer while lightly forcing it out.
Parts Used:
Drive Motor with Pulley
  • James from East Palatka, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Belt broke
Watched a you tube video on replacing a dryer belt for a whirlpool dryer. Perfect instructions. Dryer is working great.Thank you
Parts Used:
Multi Rib Belt - 92-1/4"
  • Brunner from Sykesville, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
The dryer would light in the beginning of the cycle and not come back on
I opened the 5x5" door in the front of the dryer. Unscrewed the clamp holding the two coils down replaced/reconnected the coils and screwed the clamp back down
Parts Used:
M Series New Style Coil Kit
  • Louis F from West Tisbury, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken belt
video on your website made it super easy
Parts Used:
Multi Rib Belt - 92-1/4"
  • mark from merrick, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11072514102
1321 - 1335 of 1547
Back to Top